#This file record the run list for solid ecal beamtest in HallC.
#Do not delete
5-pass beam, 10.549 GeV
=================================================================
slot 7 FADC250_DAC 3300 (for all 16 channels)
slot 8 FADC250_DAC 3300 (for all 16 channels)
20220620 21:30
HV slot 2: 0 0 0 0 0 0 0
HV slot 10: 1500 1500 1500 1500 0 0 0 0 0 0 0
2925 FADC only
2926 FADC only
2927 FADC only
2928 FADC only
2929 FADC only
File not exist for run 2930-2949, debug DAQ
20220621 12:20
HV slot 2: 900 950 900 0 0 0 0
HV slot 10: 1500 1500 1500 1500 1500 1500 1500 1800 1800 1800
2950-2956 SSP only
2957 SSP only, trash
2958 debug DAQ, trash
2959 First run for FADC+SSP, good data
2960 good FADC+SSP data
2961-2964 DEBUG SSP, all trash
20220623 15:50
HV slot 2: 900 950 900 1500 1500 1500 1500
HV slot 10: 1600 1600 1700 1600 1500 1500 1500 1800 1800 1800
From this run, trigger lost due to FIFO has an 100mv offset
2965-2968 SSP only, no trigger and debug daq, trash
2969 FADC+SSP, no trigger, trash
2970 cosmic run, no trigger, trash
2971 beam run, no trigger, trash
From run 2972, trigger is connected to another FIFO unit which has 0 offset
20220624 12:20
HV slot 2: 900 950 900 1000 1000 1000 1000
HV slot 10: 1600 1600 1700 1600 1500 1500 1500 1800 1800 1800
2972 debug DAQ, trash
2973 good FADC+SSP data <------- First run for good Cherenkov HV
2974
2975 trash
2976-2981 good FADC+SSP data
2982 trash
2983-3002 good FADC+SSP data
3003-3005 debug DAQ, trash
3006-3013 good FADC+SSP data
3014-3015 cosmic
3016 daq crash, no output files
3017-3018 debug daq, trash
3019 cosmic
3020-3021 debug daq for DAC values and HV, trash
=====================================================================
GOOD DATA STARTED ......
=====================================================================
For all runs before 3022, slot 7 and slot 8 FADC250_DAC are 3300 for all channels. Therefore some channels might not see signal.
20220629 16:20
HV slot 2: 900 950 900 1000 1000 1000 1000
HV slot 10: 1600 1600 1850 1750 1000 1100 1800 1680 1920 1800
slot 8 FADC250_DAC 3000
slot 8 FADC250_DAC 3300 3000 3300 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
3022 First production run <-----------------
3023 DAQ crashed
3024 production
3025 debug run, cosmic, trash
=====================================================================
Cherenkov ch12 (started from 0) has cabling issue for runs before 3026
=====================================================================
Change FADC DAC for Ecal channels
slot 8 FADC250_DAC 3300 3000 3300 3000 3000 3000 3000 3000 3000 3000 3300 3300 3300 3000 3300 3000
3026 production, cosmic at the first 4 hours(~30 events), see beam around 6 pm
3027 production
3028 production
3029 production, no beam at the beginning (several hours)
3030 production
3031 production
3032 production
3033 production
3034 production
3035 production
3036 production
3037 production, daq machine tunl11 has some issue and vncserver crashed, so coda also crashed
3038 production, first test run after rebooting tunl11 and sbsvme22, data is good
3039 production, test auto log scripts, data is good
3040 production
3041 cosmic, trash
3042 debug daq,trash
3043 no files, daq crashed
FADC config file changed:
1) remove slot 9
2) slot 7
FADC250_ALLCH_DAC 3205 3170 3170 3195 3195 3190 3200 3195 3180 3205 3190 3215 3170 3215 3175 3205
3)slot 8
FADC250_W_WIDTH 400
FADC250_ALLCH_DAC 3500 3200 3460 3190 3220 3210 3190 3220 3220 3190 3500 3520 3510 3500 3490 3450
3044 cosmic, slot 8 FADC250_W_WIDTH 400
3045 cosmic, slot 8 FADC250_W_WIDTH 400
changed slot 7 FADC250_W_WIDTH from 200 to 400
3046 both slot 7 and slot 8, FADC250_W_WIDTH = 400
3047 production
3048 production
3049 1 event only, cosmic, end it for changing config file
==============================================================
:::::::::::::::::::::::USEFUL DATA START::::::::::::::::::::::
Before run 3050, only part of the pulse was recorded, therefore all these runs are gabages.
Runs 3050 - 3057 could be useful, but their HVs are not perfect.
==============================================================
for both slot #7 and #8, changed to the following 2 lines:
FADC250_W_OFFSET 1000
FADC250_W_WIDTH 1000
3050 debug fadc config file,FADC250_W_OFFSET=1000 and FADC250_W_WIDTH=1000
3051 debug fadc config file,FADC250_W_OFFSET=1000 and FADC250_W_WIDTH=1000
==============================================================
for both slot #7 and #8, changed to the following 2 lines:
FADC250_W_OFFSET 1060
FADC250_W_WIDTH 400
3052 debug fadc config file,FADC250_W_OFFSET=1060 and FADC250_W_WIDTH=400
3053 production
3054 production
==============================================================
HV changed
Slot 2
Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
HV: 950 980 900 1000 1000 1000 1000
Slot 10
Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B, SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
HV: 1600 1600 1750 1750 900 1000 1950 1580 1750 1750
3055 HV tripped, empty,trash
3056 production
3057 production
================================================================
::::::::::::::::::::::::GOODEN DATA START:::::::::::::::::::::::
================================================================
HV changed
Slot 2
Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
HV: 1000 1030 900 1000 1000 1000 1000
Slot 10
Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B, SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
HV: 1600 1600 1750 1750 880 1000 1950 1550 1800 1750
3058 production, 05:15 July 9th - 03:50, target=Loop 2 LH2,shms_p=8.035,shms_theta=7.83,hms_p=-2.398,hms_theta=28.19,
13:10 target changed to dummy, I=38uA,
18:43 target changed to Loop 2 LH2, I=38uA
3059 production, 03:56-15:24 July 10th,target=Loop 2 LH2,shms_p=8.035,shms_theta=7.83,hms_p=-2.398,hms_theta=28.19,
3060 production, 15:25-00:35, target=Loop 2 LH2,shms_p=8.035,shms_theta=7.83,hms_p=-2.398,hms_theta=28.19,
3061 production, 00:36-09:41 July 11th,target=Loop 2 LH2,shms_p=8.035,shms_theta=7.83,hms_p=-2.398,hms_theta=28.19,
05:55 SHMS rotated to 9.83deg, shms_p=8.035,shms_theta=9.83,hms_p=-2.398,hms_theta=28.19,
3062 production, 09:41-10:15 July 11th,target=Loop 2 LH2,shms_p=8.035,shms_theta=9.83,hms_p=-2.398,hms_theta=28.19,
3063 cosmic, 6 events
12:53 SHMS rotated to 5.65deg3064 production, 16:06-11:19 July 12th,target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
3065 production, 11:19-18:02 July 12th,target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
3066 production, 18:02-00:43,target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
3067 production, 00:45-11:48 July 13th,target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
3068 production, 11:48-02:04, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
13:15, target ladder moved to home, no target (absolute empty)
14:50, target changed to dummy
23:28, target changed to Loop 2 10cm LH2
3069 production, 02:04-09:54 July 14th, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
3070 production, 09:55 July 14th - 10:16 July 15th, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
3071 production, 10:16-03:26 July 15th, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
16:38 target changed to dummy
19:33 target changed to Loop 2 LH2
3072 production, 03:27-16:39 July 16th, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
13:29 SHMS rotated to 9.65deg, tried to get I=80uA
3073 production, 16:42-14:26 July 17th,target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
3074 production, 14:26-02:11,target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
3075 production, 02:11-10:35 July 18th,target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
3076 production, 10:16-00:39, target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
3077 production, 00:39-09:42 July 19th, target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
06:51 target changed to dummy
3078 production, 09:43-00:29 July 20th, target=dummy,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
10:04 target changed to Loop 2 LH2, target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
12:00-ish, SHMS rotated to 8.68deg, HMS rotated to 34.15deg,
target_type=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
===========================================================
3079 pulse trigger
3080 pulse trigger
3081 pulse trigger
3082 pulse trigger
===========================================================
3083-3084 trash, no data file
3085 debug daq
3086 production, 03:11-09:42 July 21st, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3087 production, 09:43-16:07 July 21st, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3088 production, 16:07-12:23 July 22nd, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3089 production, 12:23-04:28 July 23rd, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3090 production, 04:28-15:44 July 23rd, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3091 production, 15:47-05:28 July 24th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3092 production, 05:28-18:22 July 24th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3093 production, 18:22-09:32 July 25th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3094 production, 09:33-23:40 July 25th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3095 production, 23:41-09:29 July 26th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3096 production, 09:29-15:35,July 26th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
13:45 target changed to dummy
beam stopped at ~15:10 due to thunderstorm.
beam stopped at 19:00-ish, no beam for whole day of July 20th3097 production, 15:35 July 26th - 04:56 July 28th, target=dummy,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
Dummy target when this run was started. At 22:45 July 26, target ladder was changed to home(empty).
Tune beam cane at 11:27 July 27th.
12:15 July 27th, beam was stable to reach 65uA, changed target to Loop 2 LH2.
target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15
17:06 July 27th, changed target to dummy.
22:06 July 27th, changed target to Loop 2 LH2.
3098 production, 04:56-09:48 July 28th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15
updating readout list ......
Bryan added a feature to run the fixed pulser at some frequency until some number of sync events.
It's currently configured (ti_list.c) with the structure:
typedef struct
{
int enable; // enable (1) / disable (0)
int interval; // 1 sync event every interval events
int pedestal; // disable (0) / Disable after pedestal sync events
int current; // sync event counter for pedestal feature
int pulser_arg1; // fixed pulser argument. Units of 120ns.
} TI_SYNCEVENT_CONFIG;
TI_SYNCEVENT_CONFIG tiSyncEventConfig = {1, 1000, 100, 0, 83};
using hallc_ti configuation, with new ti_list.c
HV is off
3100 pulse, HV off, beam off
3101 pulse, HV off, beam off
3102 pulse, HV off, beam off
HV is on
3103 pulse, HV on, beam on
3104 pulse, HV on, beam on
3105 pulse, HV on, beam on
==========================================================================
go back to use hallc_fadc_ssp configuration, with new ti_list.c
3106 production, 11:41-12:19, target_type=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
FADC config changed to make pedestal arround 100
slot 7:
#FADC250_ALLCH_DAC 3205 3170 3170 3195 3195 3190 3200 3195 3180 3205 3190 3215 3170 3215 3175 3205
FADC250_ALLCH_DAC 3150 3120 3120 3150 3150 3140 3150 3150 3130 3160 3140 3270 3120 3170 3130 3160
slot 8:
#FADC250_ALLCH_DAC 3500 3200 3460 3190 3220 3210 3190 3220 3220 3190 3500 3520 3510 3500 3490 3450
FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3170 3170 3130 3450 3470 3460 3450 3440 3390
3107-3111 debug daq, could be good for pedestal
3112 production, daq crashed, could be good for pedestal
3113 no data file, coda can not start
==========================================================================
Reboot tunl11 and sbsvme22
3114 production, 03:02-16:52,target_type=dummy, shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
11:21, target changed to Loop 2 10cm LH2, shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
3115 production, 16:53-14:10 July 31st,target=Loop 2 10cm LH2, shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
17:14 SHMS rotated to 10.86deg, HMS rotated to 13.43deg,
beam came back at 19:35, target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=10.86,hms_p=-4.256,hms_theta=13.43,
01:01 target changed to dummy,
01:50 SHMS rotated to 8.86 deg,
01:53 target changed back to Loop 2 10cm LH2, shms_p=6.265,shms_theta=8.86,hms_p=-4.256,hms_theta=13.43,
05:12 target changed to dummy,
06:31 target changed back to Loop 2 10cm LH2,
13:12 SHMS rotated to 6.76deg, shms_p=6.265,shms_theta=6.76,hms_p=-4.256,hms_theta=13.43,
3116 production, 14:10-23:18 July 31st, target_type=Loop 2 10cm LH2,shms_p=6.265,shms_theta=6.76,hms_p=-4.256,hms_theta=13.43,I=40uA
Target changed to dummp at 14:35, then changed back to Loop 2 at 15:34,
17:58 SHMS angle changed to 7.91 deg, shms_p=6.538,shms_theta=7.91,hms_p=-3.944,hms_theta=17.5,I=40-65uA
3117 production, 23:18-09:24, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=7.91,hms_p=-3.944,hms_theta=17.5, I=40uA
Target changed to dummy at 01:40, then to Loop 1 10 cm LD2 at 02:40, beam stopped at 05:00
3118 production, 09:24-21:59, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=7.91,hms_p=-3.944,hms_theta=17.5, I=40uA
3119 production, 21:59-11:40, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=7.91,hms_p=-3.944,hms_theta=17.5, I=40uA,
SHMS rotated to 9.915deg at 5:25 20220802, after that, shms_p=6.538,shms_theta=9.91,hms_p=-3.944,hms_theta=17.5, I=50-65uA
3120 production,11:42-23:49, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=9.91,hms_p=-3.944,hms_theta=17.5
Target changed to 10cm dummy at 17:39, then changed to Loop 2 10 cm LH2 at 18:47, this run finished at 23:49
3121 production, 23:51-08:56, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=9.91,hms_p=-3.944,hms_theta=17.5, I=70uA
no beam for the fisrt 8 hours
GEM gas bottle might be emtpy ... need to verify from data
3122 production, 08:56-11:14, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=9.91,hms_p=-3.944,hms_theta=17.5, I=70uA
SHMS rotated to 11.91 deg at 10:25, shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5,
3123 production, 11:14-14:47, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
3124 production, 14:48-17:39, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
GEM HV is off
3125 production, 17:45-20:07, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
change target to dummy
3126 production, 20:22-21:07, target_type=dummy,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
====================================================================
FADC slot 7.11 DAC value changed from 3270 to 3170
slot 7:
#FADC250_ALLCH_DAC 3205 3170 3170 3195 3195 3190 3200 3195 3180 3205 3190 3215 3170 3215 3175 3205
#FADC250_ALLCH_DAC 3150 3120 3120 3150 3150 3140 3150 3150 3130 3160 3140 3270 3120 3170 3130 3160
FADC250_ALLCH_DAC 3150 3120 3120 3150 3150 3140 3150 3150 3130 3160 3140 3170 3120 3170 3130 3160
3127 production, 20:22-21:07, target_type=dummy,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
about 85k events only, but they are good events
changed target to Loop 1
3128 production, 21:11-22:41, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
3129 production, 22:42-02:35, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
changed target to Loop 2 LH2, then changed target to Loop 2 LH2.
HMS was rotated 20.57deg, SHMS was rotated to 8.46deg.
3130 production, 02:41-08:15, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58,
3131 production, 08:16-12:41, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58,
3132 production, 12:41-17:03, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58,
no beam since 15:30, thunderstorems affect accelerator
changed target to dummy
3133 no beam, pedestal run, 17:05-17:05
3134 no beam, pedestal run, 17:07-17:07
3135 production, 17:11-21:06, target_type=dummy,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58,
no beam for the first 100k events
3136 production, 17:11-23:58, target_type=dummy,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58, I=40uA
no beam for the first 100k events
3137 production, 23:58-0:16, target_type=dummy,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58, I=40uA
SHMS rotated to 10.475deg at 0:08
3138 production, 0:16-1:09, target_type=dummy,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=40uA
3139 production, 1:10-02:11, target_type=dummy,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=40uA
changed target to Loop 2 10cm LH2
3140 production, 2:13-8:25, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=40uA
3141 no beam, pedestal run
08:43 HV is off
10:23 HV is ON
3142 no beam, pedestal run
3143 no beam, pedestal run
3144 production, 14:08-21:39, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=40uA
no beam during the first 100k events. Beam was on for just several minutes.
3145 production, 21:40-11:20, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=70uA
no beam during the first 100k events. beam started at 4:05
3146 production, 11:20-15:44, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=70uA
SHMS angle changed to 12.49 deg at 12:16
3147 production, 15:44-01:39 August 7th, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=12.49,hms_p=-3.716,hms_theta=20.58
daq rate 1.5kHz @ I=70uA
18:20 target changed to dummy
22:00 target changed to Loop 2 LH2, I=70uA
3148 production, 01:39-07:24 August 7th, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=12.49,hms_p=-3.716,hms_theta=20.58
beam stopped at 7:00
7:30 SHMS rotated 12.28 deg, HMS rotated to 15.06 deg, target was changed to Loop 1 10cm LD2
===================================================================
FADC250_W_WIDTH = 240 for both slot7 and slot8
3149 pedestal run, no beam
3150 pedestal run, no beam
3151 production, 07:34-13:32, target_type=Loop 1 10cm LD2,
shms_p=-5.127,shms_theta=12.29,hms_p=-5.309,hms_theta=15.04, I=75uA
From 10:47 to 11:11, target was changed to dummy (I=40uA), at
11:42 target was changed back to Loop 1 10cm LD2, I=75uA
At 12:42, SHMS was ratated to 14.29deg, at this angle, daq rate 5.5kHz
subrun 0-50: SHMS=12.29deg
subrun 51: SHMS=12.29deg and 14.29deg
subrun 52-60: SHMS=14.29deg
3152 production, 13:32-17:50 August 7th, target_type=Loop 1 10cm LD2,
shms_p=-5.127,shms_theta=14.29,hms_p=-5.309,hms_theta=15.04,
I=75uA, daq rate 5.5kHz
16:37 target changed to dummy, I=40uA
17:25 target changed to Loop 1 10cm LD2, I=75uA
17:42 SHMS rotated to 16.28deg, I=75uA, daq rate 5.5kHz
subrun 0-42: SHMS=14.29deg
subrun 43: SHMS=14.29deg and 16.28deg
subrun 44-45: SHMS=16.28deg3153 production, 17:50-19:26, target_type=Loop 1 10cm LD2, shms_p=-5.127,shms_theta=16.28,hms_p=-5.309,hms_theta=15.04,I=75uA
3154 production, 19:26-00:01, target_type=Loop 1 10cm LD2, shms_p=-5.127,shms_theta=16.28,hms_p=-5.309,hms_theta=15.04,I=75uA
23:35 changed to dummy target,I=40uA, daq rate 1.6kHz
3155 production, 00:02-00:33, target_type=dummy, shms_p=-5.127,shms_theta=16.28,hms_p=-5.309,hms_theta=15.04,I=40uA,
daq rate 1.6kHz, beam stopped at 00:14
20220808 00:14, rotated SHMS to 16.91 deg, HMS to 19.92 deg
3156 production, 00:37-01:48, target_type=dummy,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91,I=40uA,
daq rate 1.6kHz,
target changed to Loop 1 10cm LD2 at 01:16,
target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
3157 production, 00:37-03:11, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
daq rate 5.6kHz
3158 production, 03:11-09:11, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
no beam for the fisrt 100k events, daq rate 5.6kHz
3159 production, 09:11-10:09, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
daq rate 5.6kHz
3160 production, 10:10-13:24, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
daq rate 5.6kHz
3161 production, 13:24-15:44, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
daq rate 5.6kHz
target changed to dummy at 15:18, I=40uA
3162 production, 15:44-16:32, target_type=dummy,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=40uA
beam stop at 16:03 to prepare for optic
16:09 target changed to single foil Carbon 0.5%, SHMS rotated to 6.8deg and HMS ratated to 12.5deg
3163 production, 16:32-17:22, target_type=Carbon 0.5%, shms_p=-8.55,shms_theta=6.8,hms_p=-5.587,hms_theta=12.48,I=75uA
no beam for the first 100k events, daq rate 160Hz
Target move to Optics 1 +/- 8cm, 2 Foils Carbon
3164 production, 17:22-17:47, target_type=Optics 1 z=+/-8cm, 2 Foil, shms_p=-8.55,shms_theta=6.8,hms_p=-5.587,hms_theta=12.48,I=50uA
no beam for the first 100k events, daq rate 80Hz
3165 production, 17:47-18:02, target_type=Optics 1 z=+/-8cm, 2 Foil, shms_p=-8.55,shms_theta=6.8,hms_p=-5.587,hms_theta=12.48,I=50uA
only 30k triggers
18:00 target changed to Loop 2 10cm LH2
3166 production, 18:05-18:57, target_type=Loop2 10cm LH2, shms_p=-8.55,shms_theta=6.8,hms_p=-5.587,hms_theta=12.48,
I=60uA (18:06), then 20uA(18:08) then 10uA(18:10)
daq rate 130Hz @20uA, 65Hz @10uA
SHMS rotated to 7.5deg at 18:28, shms_p=-8.55,shms_theta=7.5,hms_p=-5.587,hms_theta=12.48,I=15uA
18:57 Target changet to Optics 1 /- 8 cm
3167 production, 18:59-19:37, target_type=Optics 1 z=/-8cm, shms_p=-8.55,shms_theta=7.5,hms_p=-5.587,hms_theta=12.48,I=50uA
daq rate 90Hz @50uA
target changed to Carbon 0.5% at 19:20, I=75uA
19:38 SHMS rotated to 8.3 deg
3168 production, 19:39-19:54, target_type=Carbon 0.5%, shms_p=-8.55,shms_theta=8.3,hms_p=-5.587,hms_theta=12.48,I=75uA
19:54 Target changet to Optics 1 +/- 8 cm
3169 production, 19:54-20:34, target_type=Optics 1 z=+/-8cm, shms_p=-8.55,shms_theta=8.3,hms_p=-5.587,hms_theta=12.48,I=50uA
no beam for the first 100k events,
daq rate 90Hz @50uA
20:24 target changed to Loop 2 10cm LH2, beam came back at 20:29
3170 production, 20:34-21:23, target_type=Loop 2 10cm LH2, shms_p=-8.55,shms_theta=8.3,hms_p=-5.587,hms_theta=12.48,I=20uA
daq rate 160Hz @20uA, beam stopped at 21:06
===================================================
HV map for FTBF beam test
- # SDU#4 SDU#5 THU#2 SDU#2 SDU#1 THU#1
SC1 SC2 Ecal1 Ecal2 Ecal3 PrSh1 PrSh2 PrSh3
-1260 -1280 -760 -860 -880 -1640 -1480 -1800 <<== 1~8GeV
This setting was also used for some 1GeV calibrations
-1260 -1300 -880 -920 -940 -1640 -1440 -1800 <<== <1GeV
---------------------------------------
4GeV calibration start
1009 Moved table to (1505, 337), center on the left block 51,563 events
1010 Moved table to (1389, 337), center on the right block 77621 events
1011 Moved table to (1447, 243), center on the top block 52034 events
4GeV calibration end
---------------------------------------
---------------------------------------
1GeV calibration start, MWPC 1 is not working
796 move to Top block, use this New HV: 1260, 1300, 880, 920, 940, 1640, 1440, 1800, FADC ch11 and ch12 swapped.
These two channels are down stream Cherenkov. After swapped, Down cherenkov inner PMT is in ch12.
797
798 move to left block, point B (1498,347)
799
800 beam on the center of the left block, point B
801
802 beam on the center of the right block, point C (1382,347)
803 beam on the center of the top block, point A (1440, 252)
1GeV calibration end
---------------------------------------
=====================================================
change HV to the same as FermiLab
- # SDU#4 SDU#5 THU#2 SDU#2 SDU#1 THU#1
SC1 SC2 Ecal1 Ecal2 Ecal3 PrSh1 PrSh2 PrSh3
-1260 -1280 -760 -860 -880 -1640 -1480 -1800 <<== 1~8GeV
===>
slot10.7(SDU#1) slot10.8(THU#1) slot10.9(SDU#2)
-1480 -1800 -1640
slot2.0(SDU#4) slot2.1(THU#2) slot2.2(SDU#5)760 -880 -860
----------------------------------------------
21:40 SHMS rotated to 12.25deg, HMS rotated to 15.7deg
22:11 target changed to dummy
3171 production, 22:10-22:21,target_type=dummy,shms_p=-8.035,shms_theta=12.25,hms_p=-6.792,hms_theta=15.69,I=40uA
no beam at the first 100k triggers
22:34 SHMS rotated to 13.15deg, HMS rotated to 17.72deg
3172 production, 22:22-23:22,target_type=dummy,shms_p=-8.035,shms_theta=13.15,hms_p=-6.792,hms_theta=17.72,
no beam at the first 100k triggers, beam came at 22:32. only 9 minutes of dummy data
22:41 stopped beam to changed target to Loop 2 10cm LH2
22:46 beam came back and then went away at 22:53 due to HMS Q1 interlock,
23:12 beam came back again, shms_p=-8.035,shms_theta=13.15,hms_p=-6.792,hms_theta=17.72, I=60uA,
daq rate 1.1kHz, 10 minutes of LH2 data
3173 production, 23:22-23:52 August 8th,
target=Loop 2 10cm LH2, shms_p=-8.035,shms_theta=13.15,hms_p=-6.792,hms_theta=17.72, I=60uA
daq rate 1.1kHz
beam stopped at 23:38 then SHMS rotated to 14.02 deg and HMS rotated to 19.86deg
beam came back at 23:49, I=75uA, shms_p=-8.035,shms_theta=14.02,hms_p=-6.792,hms_theta=19.86,
subrun 0: SHMS=13.15deg
subrun 1: SHMS=13.15deg and 14.02deg3174 production, 23:52-02:03 August 9th,
target=Loop 2 10cm LH2, shms_p=-8.035,shms_theta=14.02,hms_p=-6.792,hms_theta=19.86, I=75uA
daq rate 1.9kHz
0:51 target changed to dummy, I=40uA,
01:16 SHMS rotated to 14.895deg, shms_p=-8.035,shms_theta=14.9,hms_p=-6.792,hms_theta=19.86, I=75uA
01:45 target changed to Loop 2 LH2, beam came back at 01:49 but stopped at 01:58
subrun 0-3 are for 14.02 deg SHMS
subrun 4 are for both 14.02 and 14.9 deg SHMS
subrun 5-6 are for 14.9 deg SHMS
3175 production, 02:03-08:35,target=Loop 2 10cm LH2, shms_p=-8.035,shms_theta=14.9,hms_p=-6.792,hms_theta=19.86,I=75uA
no beam at the first 100k triggers,beam came back at 03:18,
04:45, SHMS rotated to 15.785deg, shms_p=-8.035,shms_theta=15.79,hms_p=-6.792,hms_theta=19.86,I=70uA
06:05, target changed to dummy, I=40uA, took 8 minutes of data
06:25, SHMS rotated to 13.58deg, took 8 minutes of data for dummy, I=40uA,
06:47, changed target to Loop2 LH2, shms_p=-7.913,shms_theta=13.58,hms_p=-6.792,hms_theta=19.86,
08:00, SHMS rotated to 12.69deg, took 4 minutes of data till beam stopped at 08:04 to change pass,
shms_p=-8.035,shms_theta=12.69,hms_p=-6.792,hms_theta=16.03,I=70uA
==============================================================================================================
Aug 9th 08:05 Accelerator changed beam from 5-pass to 4-pass for Hall C. Beam energy is 8.494GeV
3176 pedestal, 100k pulse triggers, no beam
3177 pedestal, 100k pulse triggers, no beam
08:48 HMS rotated to 20.905deg, SHMS rotated to 6.93deg
3178 production, 09:02-15:08, target=Loop 2 LH2, shms_p=6.265,shms_theta=6.93,hms_p=-2.193,hms_theta=20.89,
no beam at the first 100k triggers,beam came back at 14:02,
14:00 target changed to Carbon Hole, I=5uA for 6 minutes,
14:18 target changed to Loop 2 LH2, I=35uA, beam came back at 14:20, daq rate 220Hz, beam stopped at 14:46
3179 production, 15:09-21:31, target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=6.93,hms_p=-2.193,hms_theta=20.89,
no beam at the first 100k triggers,beam came back at 17:31, I=60uA
22:37 target changed to dummy
3180 production, 21:31-22:28, target=dummy, shms_p=6.265,shms_theta=6.93,hms_p=-2.193,hms_theta=20.89
no beam for the first 100k triggers,
21:35 beam arrived, beam current linear ran up from 3uA to 23uA at 21:55 to do Ion Chamber calibration
From 21:56, I=40UA till 22:15
22:15 SHMS rotated to 8.93 deg, beam came back at 22:20
target=dummy, shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89
3181 production, 22:28-22:44, target=dummy, shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89
22:46 target changed to Loop 2 LH2
3182 production, 22:48-00:05 August 10th,
target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89, I=80uA
no beam for the first 100k triggers,daq rate 770Hz
3183 production, 00:05-01:22,
target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89, I=80uA
daq rate 770Hz, beam stopped at 00:49 due to Vacuum issue at VBV3H08A
3184 pedestal, pulse run, 01:23-10:26, no beam for the whole run,1000006 events
3185 pedestal, pulse run, 11:29-11:29, no beam
=========================================================================================
Add "PreSh_t && Shower_t" into TS#2, 20220810
3186 pedestal, pulse run, 14:54-15:19, no beam
3187 pedestal, pulse run, 15:47-15:47, no beam
16:00 SHMS rotated to 5.5 deg.
3188 production, 17:21-23:07, target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=5.53,hms_p=-2.193,hms_theta=20.89,
no beam for the sirst 100k triggers, tune beam arrived at 17:52, real beam arrived at 21:34
23:09 Changed FADC slot8.9 DAC value from 3130 to 3440. After feed it into FIFO, its pedestal changed
3189 production,23:10-02:38 August 11th,
target=Loop 2 LH2, shms_p=6.265,shms_theta=5.53,hms_p=-2.193,hms_theta=20.89,I=30uA
daq rate 320Hz
3190 production,02:38-04:38, target=Loop 2 LH2, shms_p=6.265,shms_theta=5.53,hms_p=-2.193,hms_theta=20.89,I=30uA
daq rate 320Hz
03:05 target changed to dummy, I=40uA
03:45 HMS rotated to 28.41deg,
target=dummy,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41, I=40uA, daq rate 320Hz
3191 production, 04:39-09:03, target=dummy,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
I=40uA, daq rate 320Hz
4:50 target chagned to Loop 2 LH2, I=35uA
target=Loop 2 LH2, shms_p=6.265,shms_theta=5.53,hms_p=-2.193,hms_theta=28.41,I=35uA
Acceleration maintenence started from 6:30
3192 production, 19:55-01:52 August 12th, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
no beam for the first 100k triggers, tune beam came back at 23:32
3193 production, 01:52-09:28, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
daq rate = 400Hz @ I=38uA. Beam stopped at 09:10
09:21 A beam energy measurement is scheduled at 9:30-ish AM. Target parked at 'home'.
11:29 Target changed to Loop 2 LH2
3194 production, 11:35-12:26, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
no beam for the first 100k triggers, beam came back at 11:50 and went away at 12:01
3195 production, 14:05-14:41, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
daq rate = 400Hz @ I=38uA.
3196 production, 14:42-16:46, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
no beam for the first 100k triggers, beam came back at 14:49
beam stopped at 16:12
3197 production, 16:49-00:54 August 13th, target=Loop 2 LH2,
shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
no beam for the first 100k triggers, beam came back at 17:48
3198 production, 00:54-02:28, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
daq rate = 450Hz @ I=40uA.
01:09 SHMS rotated to 7.47 deg, trying to ramp beam current up to 80uA
subrun 0: 5.53deg and 7.47deg
subrun 1-3: 7.47deg
3199 production, 02:28-12:05, target=Loop 2 LH2,shms_p=6.538,shms_theta=7.47,hms_p=-1.882,hms_theta=28.41,
daq rate = 1024Hz @ I=79uA.
3200 production, 12:05-14:42, target=Loop 2 LH2,shms_p=6.538,shms_theta=7.47,hms_p=-1.882,hms_theta=28.41,
daq rate = 1024Hz @ I=79uA.
14:28 target changed to dummy, I=40uA, daq rate 320Hz
3201 production, 14:42-16:01, target=dummy,shms_p=6.538,shms_theta=7.47,hms_p=-1.882,hms_theta=28.41,
I=40uA, daq rate 320Hz
16:01 SHMS rotated to 9.5deg, target changed to Loop 2 LH2
3202 production, 14:01-17:29, target=Loop 2 LH2,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
no beam for the first 100k triggers, beam came back 16:04
daq rate = 1024Hz @ I=79uA.
beam stopped at 17:13, 4th pass separation issue
3203 production, 17:37-00:35 August 14th, target=Loop 2 LH2,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
no beam for the first 100k triggers, beam came back 17:41
daq rate 1.5kHz @ I=80uA
3204 production, 00:35-03:53 August 14th, target=Loop 2 LH2,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
daq rate 1.5kHz @ I=80uA
03:31 target changed to dummy, I=40uA
3205 production, 03:53-04:13, target=dummy,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
I=40uA, daq rate 512Hz
3206 production, 04:13-04:31, target=dummy,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
I=40uA, daq rate 512Hz
04:38 target changed to Loop 2 LH2
04:50 SHMS rotated to 8.93 deg, HMS rotated to 20.89deg
3207 production, 05:01-13:02, target=Loop 2 LH2,shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89,
no beam for the first 100k triggers, beam came back 7:35, I=80uA
beam stopped at 10:32, then came back at 12:15
~11:00 SHMS rotated to 30.02deg, HMS rotated to 19.56deg
target=Loop 2 LH2,shms_p=3.731,shms_theta=30.02,hms_p=-5.587,hms_theta=19.56
---> SHMS=8.93deg for subrun 0-3, SHMS=30.02deg for subrun 5 to 10, subrun 4 contains both angles <---
3208 production, 13:02-13:14, target=Loop 2 LH2,shms_p=3.731,shms_theta=30.02,hms_p=-5.587,hms_theta=19.56,I=80uA
At 13:07, target changed to dummy, I=40uA. Only 2 minutes of LH2 target then 2 minutes of dummy target
3209 production, 13:14-13:25, target=dummy,shms_p=3.731,shms_theta=30.02,hms_p=-5.587,hms_theta=19.56,
daq rate 1.5kHz @ I=40uA
3210 production, 13:25-13:30, target=dummy,shms_p=3.731,shms_theta=30.02,hms_p=-5.587,hms_theta=19.56,
daq rate 1.5kHz @ I=40uA, only 2 minutes of data then beam stopped for target change
13:32 target changed to Loop 2 LH2,
13:32 SHMS rotated to 28.355deg. HMS rotated to 20.905deg
3211 production, 13:33-13:44, target=Loop 2 LH2, shms_p=3.996,shms_theta=28.40,hms_p=-5.321,hms_theta=20.91,
daq rate 1.8kHz @ I=80uA, beam stopped at 13:41
3212 production, 13:45-14:39, target=Loop 2 LH2, shms_p=3.996,shms_theta=28.40,hms_p=-5.321,hms_theta=20.91,
daq rate 1.8kHz @ I=80uA,
I stopped coda at 13:44 for previous run because HallC coda was stopped at 13:41 in order to adjust
SHMS angle from 28.44 to 28.355.
I was taking data during this adjustment. This change should not affect the ecal setup.
14:40 target changed to dummy
3213 production, 14:41-14:58. target=dummy, shms_p=3.996,shms_theta=28.355,hms_p=-5.321,hms_theta=20.91,
I=40uA, daq rate 620Hz
15:00 target changed to Loop 2 LH2,
15:30 Set HMS angle to 15.065 and SHMS angle to 9.455 deg, but stayed at 15.05 deg and 9.53deg
3214 production, 15:01-17:03, target=Loop 2 LH2, shms_p=-7.559,shms_theta=9.53,hms_p=-6.477,hms_theta=15.05,
no beam for the first 100k triggers, beam came back 15:37, I=20uA
15:51 target changed to dummy,shms_p=-7.559,shms_theta=9.53,hms_p=-6.477,hms_theta=15.05,
16:38 SHMS rotated to 11.97 deg,HMS rotated to 15.62 deg
target=dummy, shms_p=-7.106,shms_theta=11.97,hms_p=-5.878,hms_theta=15.62,
17:02 target changed to Loop 2 LH2, shms_p=-7.106,shms_theta=11.97,hms_p=-5.878,hms_theta=15.62,
subrun 0: SHMS=9.455deg and 11.97deg
subrun 1: SHMS=11.97deg
3215 production, 17:05-17:50, target=Loop 2 LH2, shms_p=-7.106,shms_theta=11.97,hms_p=-5.878,hms_theta=15.62,
no beam for the first 100k triggers, beam came back at 15:11, I=10uA,
beam went away at 17:24 due to injector problem, only 3~4 minutes of beam in this run, 175k events
3216 production, 17:57-19:49, target=Loop 2 LH2, shms_p=-7.106,shms_theta=11.97,hms_p=-5.878,hms_theta=15.62,
no beam for the first 100k triggers, beam came back at 18:17, I=10uA till 18:45
18:47 SHMS rotated to 13.92, HMS rotated to 17.96deg, beam came at 19:13, I=55uA
target=Loop 2 LH2, shms_p=-6.72,shms_theta=13.92,hms_p=-5.878,hms_theta=17.96,
subrun 0: SHMS=11.97deg and 13.92deg
subrun 1-4: SHMS=13.92deg
3217 production, 19:49-19:54, target=Loop 2 LH2, shms_p=-6.72,shms_theta=13.92,hms_p=-5.878,hms_theta=17.96,
beam stopped at 19:51, only 256k events
19:56 target changed to dummy
3218 production, 19:57-20:11, target=dummy, shms_p=-6.72,shms_theta=13.92,hms_p=-5.878,hms_theta=17.96,
20:12 SHMS rotated to 14.82 deg, HMS rotated to 20.37deg
3219 production, 20:13-20:36, target=dummy, shms_p=-6.538,shms_theta=14.82,hms_p=-5.878,hms_theta=20.37,
no beam for the first 100k triggers, beam came back at 20:20, I=40uA, daq rate 1920Hz
20:35 target changed to Loop 2 LH2
3220 production, 20:40:21:16, target=Loop 2 LH2, shms_p=-6.538,shms_theta=14.82,hms_p=-5.878,hms_theta=20.37,
no beam for the first 100k triggers, beam came back at 20:42, I=80uA,
beam stopped at 21:12 to prepare optics runs
21:18 HMS rotated to 13 deg, target changed to Carbon 0.5%
3221 production, 21:16-22:05, target=Carbon 0.5%,
Sieve Optics,shms_p=-6.538,shms_theta=14.82,hms_p=-5.878,hms_theta=12.98,
no beam for the first 100k triggers, beam came back at 21:30,
I=4.5uA --> daq rate 64Hz,
I=13uA --> daq rate 192Hz,
I=80uA --> daq rate 1216Hz,
22:02 target changed to optics 1, Carbon +/- 8cm, I=3uA
3222 production, 22:05-23:21, target=Opitcs 1, Carbon 2-foils +/- 8cm,
Sieve Optics,shms_p=-6.538,shms_theta=14.82,hms_p=-5.878,hms_theta=12.98,
ramp currunet from 2uA till 40 uA
I= 10uA --> daq rate 128Hz
I= 15uA --> daq rate 192Hz
I= 20uA --> daq rate 256Hz
I= 49.5uA --> daq rate 576Hz
23:24 target changed to Loop LH2
23:30 SHMS rotated to 16.100deg, HMS rotated to 17.235deg
3223 production, 23:27-00:06, target=Loop 2 LH2, shms_p=-6,shms_theta=16.17,hms_p=-5.587,hms_theta=17.23,
no beam for the first 100k triggers, beam came back 23:47,
daq rate is 1.2kHz @ I=25uA
3224 production, 00:06-00:30, target=Loop 2 LH2, shms_p=-6,shms_theta=16.17,hms_p=-5.587,hms_theta=17.23,
daq rate is 1.280Hz @ I=25uA
00:30 target changed to dummy
3225 production, 00:32-01:24, target=dummy, shms_p=-6,shms_theta=16.17,hms_p=-5.587,hms_theta=17.23,
no beam for the first 100k triggers, beam came back 00:35,not staple until 00:42
daq rate 1.8 kHz @ I=40uA
3226 production, 01:24-01:36, target=dummy, shms_p=-6,shms_theta=16.17,hms_p=-5.587,hms_theta=17.23,
01:38 SHMS rotated to 19.20deg, HMS rotated to 19.505deg
3227 production, 01:39-03:02, target=dummy, shms_p=-5.646,shms_theta=19.28,hms_p=-5.587,hms_theta=19.5,
no beam for the first 100k triggers, beam came back 02:42,
03:05 changed target to Loop 2 LH2
3228 production, 03:04-03:48, target=Loop 2 LH2,shms_p=-5.646,shms_theta=19.28,hms_p=-5.587,hms_theta=19.5,
daq rate 3.7 kHz I=73uA I=77uA
daq rate 3.9 kHz
03:51 SHMS Rotated to 23.3 degrees, HMS Rotated to 21.875 degrees
3229 production, 03:53-5:44, target=Loop 2 LH2, shms_p=-4.902,shms_theta=23.2,hms_p=-5.587,hms_theta=21.875,
no beam for the first 100k triggers, beam came back at 04:37,
daq rate 3.9 kHz @ I=77uA
05:45 changed target to dummy
3230 production, 05:48-06:04, target=dummy, shms_p=-4.902,shms_theta=23.2,hms_p=-5.587,hms_theta=21.875,
no beam for the first 100k triggers, beam came back at 05:53, stopped at 5:58
daq rate 1.8 kHz @ I=40uA
3231 production, 6:06-06:18, target=dummy, shms_p=-4.902,shms_theta=23.2,hms_p=-5.587,hms_theta=21.875,
daq rate 1.8 kHz @ I=40uA
06:18 Rotated SHMS to 25.1 deg, rotated HMS to 40 deg, change momenta for both of them,
3232 pedestal run, internal pulse, no beam since 06:18
Something went wrong, Hall C configuration change could not finish within 45 minutes and further more
the injector has some problem. HallC has been scheduled a controlled access up to six hours from 8AM
for the aerogel exchange.
11:46 target changed to Loop 2 LH2
12:40 SHMS rotated to 18.9deg, HMS rotaed to 12.11deg
3233 production, 13:36-14:03, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
daq rate 4.0 kHz @ I=79uA
3234 production, 14:03-15:10, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
daq rate 3.9 kHz @ I=77uA
3235 production, 15:11-15:53, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
3236 production, 15:53-16:15, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
3237 production, 16:16-17:58, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
no beam for the first 100k triggers, beam came back at 16:40,
daq rate 4.0 kHz @ I=79uA
18:00 changed target to dummy
3238 production, 18:02-18:16, target=dummy, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
no beam for the first 100k triggers, beam came back at 18:04,
daq rate 1.9 kHz @ I=40uA
3239 production, 18:17-19:09, target=dummy, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
daq rate 1.9 kHz @ I=40uA
19:10 target changed to Loop 2 10 cm LH2
19:12 SHMS rotated to 21.22deg
3240 production, 19:14-20:38, target=Loop 2 LH2, shms_p=2.792,shms_theta=21.22,hms_p=-5.587,hms_theta=12.11,
daq rate 4.0 kHz @ I=79uA
3241 production, 20:39-21:41, target=Loop 2 LH2, shms_p=2.792,shms_theta=21.22,hms_p=-5.587,hms_theta=12.11,
daq rate 4.0 kHz @ I=79uA
21:35 target changed to dummy, beam came back at 21:40,
the last one minutes is dummy events, I=40uA, daq rate 1.8kHz
3242 production, 21:41-22:14, target=dummy, shms_p=2.792,shms_theta=21.22,hms_p=-5.587,hms_theta=12.11,
I=40uA, daq rate 1.8kHz
22:15 target changed to Loop 2 LH2, SHMS rotated to 23.215deg, actually it is 22.9deg
3243 production, 22:17-23:28, target=LH2, shms_p=2.792,shms_theta=22.9,hms_p=-5.587,hms_theta=12.11,
I=76uA, daq rate 3.9kHz
3244 production, 23:28-00:05, target=LH2, shms_p=2.792,shms_theta=22.9,hms_p=-5.587,hms_theta=12.11, I=80uA
23:35 beam stopped, changed to dummy target, beam came back at 23:44, I=40uA
subrun 0 --> LH2
subrun 1 --> part LH2 and part dummy
subrun 2 --> dummy
00:11 SHMS rotated to 21.22 deg on camera(true angle is 20.9 after subtracting offset), target changed to LH2
The SHMS angle in HallC log is 22.17, that is a typo
3245 production, 00:05-00:51, target=LH2, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
no beam for the first 100k triggers, beam came back at 00:16,
beam went away at 00:25 due to accelerator issue, 129k events
3246 production, 00:59-04:21, target=LH2, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
no beam for the first 100k triggers, beam came back at 03:15,
1kHz I=20uA I=65uA
3.2kHz
3247 production, 04:21-05:02, target=LH2, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
1.4kHz @ I=29uA
05:03 changed to dummy target
3248 production, 05:07-05:36, target=dummy, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
1.4kHz @ I=30uA
3249 production, 05:37-10:28, target=dummy, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
no beam for the first 100k triggers, beam came back at 5:55 last till 6:03.
Since 6:03, HMS Q1 was tripped, Hall C could not take beam.
06:37 target changed to LH2
08:03, beam was back again, I=12uA, target=LH2, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11,
09:10, beam stopped for pass changed
subrun 0 has both dummy and LH2 target
subrun 1 and 2 are for LH2 target only
=======================================================================================================
09:15 August 16th, started to change to 3-pass beam , E = 6.399 GeV
09:30 SHMS rotated to 17.91 deg, camera shows 18.23 due to the encoder offset 0.32.
12:00 Reset SHMS angle offset to zero so the camera shows the same value as the encoder.
Set the SHMS to 17.86 degrees and the HMS to 18.31.
3250 pedestal, pulse run, cosmic 12:42 August 16th - 12:05 August 17th, 100203 events
3251 pedestal, pulse run, cosmic, 12:41-14:38, 1000021 events
memeory upgraded to 24G in daq machine tunl11.jlab.org
tune beam came back to Hall C
17:17 target changed to carbon hole
3252 16:58-17:04 pedestal, pulse run,
3253-3255 debug daq, trash
17:48 target changed to Loop2 LH2
3256 17:52-18:01 pedestal, pulse run, debug daq, good for pedestal only
3257 production, 18:08-18:16, target=LH2,shms_p=2.412,shms_theta=17.86,hms_p=-3.921,hms_theta=13.81,
3258 production, 18:22-19:35, target=LH2,shms_p=2.412,shms_theta=17.86,hms_p=-3.921,hms_theta=13.81,
daq rate 1152Hz I=25uA I=50uA
daq rate 2.3kHz
19:36 target changed to dummy
3259 production, 19:36-20:02, target=dummy,shms_p=2.412,shms_theta=17.86,hms_p=-3.921,hms_theta=13.81,
no beam for the first 100k triggers, beam came back at 19:40,
daq rate 1664Hz @ I=40uA
20:02 SHMS rotated to 19.86 deg
3260 production, 20:03-20:24, target=dummy, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
no beam for the first 100k triggers, beam came back at 20:07,
daq rate 1664Hz @ I=40uA
20:24 target changed to LH2
3261 production, 20:26-20:35, target=LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
no beam for the first 100k triggers, beam came back at 20:28,
3262 production, 20:42-21:01, target=Loop 2 LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
daq rate 2.7kHz @ I=60uA
3263 production, 21:03-21:39, target=Loop 2 LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
no beam for the first 100k triggers, beam came back at 21:16,
daq rate 2.7kHz @ I=60uA
3264 production, 21:39-21:52, target=Loop 2 LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
daq rate 2.7kHz @ I=60uA
3265 production, 21:54-22:23, target=Loop 2 LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
daq rate 2.8kHz @ I=60uA
-------- 22:25 SHMS spectrometer change to 21.85-------------
3266 production, 22:28-22:47, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81,
daq rate 3.2kHz I=70uA. Note, it seems they were pushing to reach 80 uA, so the current and rate is may fluctuate I=80uA
3267 production, 22:47-23:14, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
daq rate 3.6kHz
no beam for the first 100k triggers, beam came back at 22:49
3268 production, 23:15-23:43, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
daq rate 3.6kHz I=80uA I=80uA
3269 production, 23:43-23:55, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
daq rate 3.6kHz
3270 production, 23:56-24:04, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
daq rate 3.60kHz @ I=0uA
no beam for the first 100k triggers, beam was off for 10 minutes due to accelerator issues
3271 production, 00:07-00:15, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
daq rate 3.6kHz @ I=80uA
---------- 00:20 Switch target to Dummy ---------
3272 production, 00:19-00:45, target=10 cm Dummy, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
no beam for the first 100k triggers, beam returned at 00:24
daq rate 1.6kHz @ I=40uA
---------00:50 Switch target to LH2-------
3273 production, 00:56-02:22, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.8
daq rate 1.8kHz @ I=40uA
3274 production, 02:23-3:04, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.86,hms_p=-3.921,hms_theta=13.8
daq rate 850Hz I=20uA I=12uA
daq rate 512Hz
3275 production, 03:04-04:44, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.86,hms_p=-3.921,hms_theta=13.8
daq rate 512Hz @ I=12uA
3276 production, 04:44-8:49, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.86,hms_p=-3.921,hms_theta=13.8
daq rate 512Hz @ I=12uA
HallC was doing FADC dead time study. current changed from 12uA, to 60uA then to 30uA
06:27 HMS rotated to 18.595deg, SHMS roated to 37.97deg
07:00 I=75UA, target=LH2, shms_p=2.412,shms_theta=38,hms_p=-4.752,hms_theta=18.61,
07:28 target changed to dummy, I=40uA
07:48 HMS rotated to 21.095deg, SHMS rotated to 34.465deg
target=dummy, shms_p=2.792,shms_theta=34.49,hms_p=-4.391,hms_theta=21.11,
08:15 target changed to LH2, I=75uA
target=LH2, shms_p=2.792,shms_theta=34.49,hms_p=-4.391,hms_theta=21.11,subrun 0-6: SHMS=21.86deg
subrun 7: SHMS=21.86deg and 37.97deg
subrun 8-11: SHMS=37.97deg
subrun 12: SHMS=37.97deg and 34.49deg
subrun 13-16: SHMS=34.49deg08:59 HMS rotated to 26.55deg, SHMS rotated to 28.46deg
3277 production, 08:53-10:45, target=LH2, shms_p=3.493,shms_theta=28.47,hms_p=-3.727,hms_theta=26.56,
no beam for the first 100k triggers, beam returned at 09:30, I=75uA
10:10 target changed to dummy, I=40uA
10:27 beam stopped
===================20020818 Install VTP board=========================
From here EPICS variables are inserted into ER
SHMS at 7.66deg and HMS at 28.78deg.
3278-3283 debug daq runs. HV are off. no beam. good for pedestal
HV are turned on in the middle of run 3283, but no beam after HV is on.
3284 production, 20:20-23:14, target=LH2,shms_p=4.605,shms_theta=7.66,hms_p=-1.727,hms_theta=28.78,
no beam for the first 100k triggers, beam came back at 21:11
daq rate 750Hz I=75UA I=75UA
22:00 target changed to dummy
22:40 SHMS rotated to 9.66deg, target changed to LH2
target=LH2,shms_p=4.605,shms_theta=9.66,hms_p=-1.727,hms_theta=28.78,
daq rate 1235Hz
subrun 0 contains data for SHMS=7.66deg
subrun 1 contains data for both 7.66deg and 9.66
subrun 2-3 contains data for SHMS=9.66deg
3285 production, 23:19-00:52 August 19th, target=LH2,shms_p=4.605,shms_theta=9.66,hms_p=-1.727,hms_theta=28.78,
daq rate 1235Hz @ I=75UA
3286 production, 00:54-05:28, target=LH2,shms_p=4.605,shms_theta=9.66,hms_p=-1.727,hms_theta=28.78,
coda lost roc3 at 01:15 and did not take data since then.
03:00 changed target to dummy
03:23 SHMS rotated to 11.66deg,
03:50 target changed to LH2,shms_p=4.605,shms_theta=11.67,hms_p=-1.727,hms_theta=28.78,
3287 production, 05:29-12:57,target=LH2, shms_p=4.605,shms_theta=11.67,hms_p=-1.727,hms_theta=28.78,
8:25 SHMS rotated to 10deg and HMS to 42.23deg
target=LH2,shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
no beam between 10:09 and 11:20
daq rate 1.5kHz @ I=77uA
subrun 0-19: 11.67deg
subrun 20: 11.67deg and 10deg
subrun 21-29: 10deg
3288 production, 12:57-18:12, target=LH2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
daq rate 1.5kHz @ I=77uA
3289 production, 18:14-18:31, target=LH2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
daq rate 1.5kHz @ I=77uA
3290 production, 18:31-00:06 August 20th, target=LH2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
daq rate 1.5kHz I=77uA I=40uA
22:09 target changed to dummy, I=40uA
daq rate 512Hz
3291 production, 00:08-00:34 August 20th, target=dummy, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
daq rate 512Hz @ I=40uA
0:26 target changed to LD2
Ion chamber calibration start from 00:31
3292 production, 00:34-00:49 August 20th, target=LD2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
beam current ramped up from 0 to 32uA for Ion chamber calibration
3293 production, 00:50-08:50 August 20th, target=LD2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
daq rate 3.2kHz @ I=77uA
3294 production, 08:51-14:18 August 20th, target=LD2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
daq rate 3.2kHz I=77uA I=78.5uA
10:36 SHMS rotated to 8deg,
target=LD2, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26, daq rate 2.0kHz
subrun 0-12: SHMS=10 deg
subrun 13: SHMS=10 deg and 8 deg
subrun 14-30: SHMS=8deg3295 production, 14:18-01:19 August 21st, target=LD2, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
daq rate 2.0kHz @ I=78.5uA
00:18 taret changed to dummy, I=40uA
subrun 0-48: LD2
subrun 49: LD2 and dummy
subrun 50: dummy3296 production, 14:18-01:21 August 21st, target=dummy, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
just 106k events
3297 production, 01:24-02:54 August 21st, target=dummy, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
daq rate 500Hz @ I=40uA
02:36 changed to LH2 target, I=80uA
3298 production, 02:55-14:46 August 21st, target=LH2, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
daq rate 1000Hz @ I=78uA
3299 production, 14:46-19:00 August 21st, target=LH2, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
daq rate 1000Hz @ I=78uA
19:01 SHMS rotated to 10deg
3300 production, 19:02-00:57 August 22th, target=LH2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
daq rate 1500Hz @ I=78uA
23:47 target changed to LD2
3301 production, 00:57-02:51 August 22nd, target=LD2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
daq rate 3.5 kHz @ I=80uA
beam stopped at 02:41
02:55 target changed to LH2
03:00 SHMS rotated to 7.5deg, HMS rotated to 29.55deg
03:00 HMS Q1 interlock happened and SHMS Dipole did not response. Hall is in controlled access.
05:00 Accelerator fire alarm, no beam.
3302 pedestal, 02:51-09:09 August 22nd, no beam
10:50 SHMS rotated to 5.5deg,
3303 production, 15:01-01:04 August 23rd, target=LH2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
no beam until 16:20
daq rate 500Hz @ I=40uA
3304 production, 01:04-04:02 August 23rd, target=LH2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
daq rate 500Hz @ I=40uA
03:00 changed to dummy target
beam stop at 03:15, Trim rack W301B13 negative bulk supply fail
3305 production, 04:04-11:33 August 23rd, target=dummy, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
no beam at the beginning until 04:58
06:25 target changed to LD2
11:23 target changed to 'home' (absolute empty) for BCM calibration
==================================================================================
run 3171-3305 were using the same HV as FermiLab, but the HV for Shower_L is too low,
the amplitude of the signal is about 10mv.
Here is the new HVs:
Slot 2
Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
HV: 1080 1100 930 1050 1050 1050 1050
Slot 10
Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B, SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
HV: 1600 1600 1700 1750 850 1000 1950 1550 1800 1750
12:54 target changed to Loop 1 10cm LD2
3306 procudtion, 12:55-14:20 August 23rd, target=LD2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
no beam for the first 100k triggers, beam came back at 13:18
daq rate = 2.7kHz I=31uA I=33uA
daq rate = 3.0kHz
This daq rate is too high comparing to run 3307. The beam might scratch the target frame.
==========HV changed=======
Lower HVs for preshower_top and all 3 Ecal blocks
Slot 2
Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
HV: 1030 1050 900 1050 1050 1050 1050
Slot 10
Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B, SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
HV: 1600 1600 1700 1750 850 1000 1950 1550 1800 1700
3307 procudtion, 14:23-18:23 August 23rd, target=LD2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
daq rate = 1.7kHz @ I=31uA
==========HV changed=======
18:24 Adjusted TOP preshower (-40V) and top shower HVs (-30V)
Slot 2
Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
HV: 1030 1050 870 1050 1050 1050 1050
Slot 10
Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B, SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
HV: 1600 1600 1700 1750 850 1000 1950 1550 1800 1660
3308 procudtion, 18:25-18:34 August 23rd, target=LD2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
daq rate = 1.0kHz @ I=31uA
==========HV changed=======
SC1_top 1700 > 1680> 1640
Top preshower 1660
Top SHower 870 -> 850
06:45 SHMS rotated to 7.5 deg
3309 procudtion, 18:48-20:08 August 23rd, target=LD2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
no beam for the first 100k triggers, beam came back at 19:36
beam stopped at 19:54 due to accelerator issue.
3310 production, 20:11-03:17 August 24th, target=LD2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
daq rate 1.7kHz @I=80uA
3311 procudtion, 03:17-12:33 August 24th, target=LD2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
no beam for the first 100k triggers, beam came back at 03:18
daq rate 1.7kHz @I=80uA
8:38 changed target to dummy, I=40uA
10:40 changed target to 'home'(absolute empty) for beam energy measurement, I=100nA, daq rate=1.2kHz
3312 trash, 12:38-12:44 August 24th, target=empty(?), shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
daq rate=1.2kHz @ I=0.1uA, the beam must have scratched something, 173k events
beam energy measurement result: beam = 6394.694 +/- 3.055 MeV
15:42 changed target to Loop2 LH2
3313 procudtion, 12:52-01:06 August 25th, target=LH2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
no beam for the first 100k triggers, beam came back at 15:38
daq rate=750Hz @ I=78uA,
3314 procudtion, 01:07-08:56 August 25th, target=LH2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
daq rate=750Hz @ I=78uA,
03:00 Rotated SHMS to 26.82 deg, HMS to 28.41 deg, shms_p=3.706,shms_theta=26.82,hms_p=-3.514,hms_theta=28.41,
04:16 changed target to dummy, I=40uA
04:35 Rotated SHMS to 23.13 deg, HMS to 33.37 deg, shms_p=4.22,shms_theta=23.13,hms_p=-3.014,hms_theta=33.37,
05:15 changed target to LH2
3315 procudtion, 08:57-10:27 August 25th, target=LH2, shms_p=4.22,shms_theta=23.13,hms_p=-3.014,hms_theta=33.37,
daq rate=3.0kHz @ I=78uA,
beam stopped at 09:03, 777k evnets
09:30 Rotated SHMS to 8.0 deg and HMS to 42.23deg
SBSVME22 lost connection. USB stick failed. No access until next accelerator maintenance day.
can not control MPOD utill the 20220916.
==============================================================================================
3318 pedestal, test daq, no beam, HV on
3319 pedestal, test daq, no beam, HV on
20220917 23:23
3320 gem pedestal run, GEM HV was not on for this run
3321 trash run, pulser event enabled, unable to check GEM signal
first 100k pulse event are disabled3322 beam seems stopped
23:51 still no beam
00:28 no beam
01:50 still no beam
02:22 beam delivery suspended due to transport ion chamber failure
3323 Latency check, initial latency value 49
3324 initial latency value 49 -- (49 is too late)
3325 & 3326 scan for value 52
3327 & 3328 scan for value 55 -- (this seems good, also consistent with Ezekiel's INFN setup)
3329 & 3330 & 3331 & 3332 scan for value 58 (seems too early)
3333 & 3334 scan for value 64 -- (64 is too early)
3335 & 3336 scan for value 60 -- (too early)
3337 production, 00:25 - 11:06 Sep. 19th, run with new GEM latency 55, (55 is too early)
3338 procudtion, 11:24 Sep 19th - 18:34 Sep. 20th, run with slightly modifed latency 52.
target=Fe, shms_p=-8.55,shms_theta=8.3,hms_p=1.82,hms_theta=48.3,
13:10 Sep 19th, changed target to B10
14:16 Sep 19th, changed target to B4C-11
16:00 Sep 19th, beam stopped till 00:24 Sep 20th
05:03 Sep 20th, changed target to Ca40, HMS roated to 66.4deg, HMS_p was set to 1.325
target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
09:00 Sep 20th, RF study started, no beam till 21:12
3339 production, 01:58 - 12:43 Sep 21st,
beam was bad, accelarator worked at about 50% efficiency
target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
10:44, SHMS Q1 vacuum issiu. Beam stopped.
11:54, Beam came back but last for 10 minutes only then went away.
3340 production,13:07 Sep 21st - 12:03 Sep 22nd,
target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
3341 production,12:04 Sep 22nd - 23:35 Sep 22nd,
target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
3342 production,23:36 Sep 22nd - 15:21 Sep 23rd,
target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
beam stopped due to vacuum issue at around 9:16.
3343 production,20:06 Sep 23rd -
target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
daq crashed at 02:22 Sep 25th
Tunl11 lost mounting disk, vncserver can not start properly
3344 daq crashed, no data file3345 productin, 21:02 Sep 25th - 03:51 Sep 26th
target=carbon, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
daq rate 250Hz
target changed to B4C-10
3346 production, 03:59 - 11:18 Sep 26th
target=B4C-10, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
beam stopped at ~05:45
3347 production, 11:20 Sep 26th - 20:34 Sep 27th, no beam until 20:12 Sep 26th.
target=B4C-10, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
20:30 target changed to Ca48
target=Ca48,shms_p=-8.55,shms_theta=8.3,hms_p=1.82,hms_theta=48.33,
03:51 Sep 27th, target changed to Ca40
04:19 Sep 27th, target changed to Carbon
04:35 Sep 27th, target changed to Beryllium
05:12 Sep 27th, target changed to B4C-10
05:40 Sep 27th, target changed to B4C-11
06:00 Sep 27th, target changed to Beryllium
13:42 Sep 27th, target changed to B4C-10
beam stopped at 17:20, Sep 27th
3348 production, 20:51, Sep 27th - 15:27 Sep 28th, no beam until 02:49 Sep 28th.
22:18 Sep 27th, target changed to B4C-11
target=B4C-11, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
09:59 Sep 28th, target changed to B4C-10
14:35 Sep 28th, target changed to Beryllium
3349 production, 15:28, Sep 28th - 10:40 Sep 29th, no beam until 20:12 Sep 26th.
target=Beryllium, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4, rate=500Hz
18:51 target changed to Loop 1 LD2
20:20 target changed to Fe
beam stopped at 7:00 Sep 29th.
3350 trash, daq test
18:14 SHMS rotated to 26deg
3351 pedestal, 18:21 - 18:27 Sep 29th, no beam
3352 production, 18:28 Sep 29th - 22:32 Oct 1st, no beam until 22:34
23:04 Sep 29th, target changed to Carbon hole
target=Carbon Hole, shms_p=-4.935,shms_theta=26.02,hms_p=6.476,hms_theta=20.69,
23:30 Sep 29th, beam stopped
23:31 Sep 29th, target changed to Loop 2 LH2
10:04 Oct 1st, tune beam came back
target=LH2, shms_p=-4.935,shms_theta=26.02,hms_p=6.476,hms_theta=20.69,
15:38 Oct 1st, target changed to Caron
15:57 Oct 1st, Target changed to LH2
17:01 Oct 1st, SHMS at 9.24 deg and HMS at 29.39 deg
target=LH2, shms_p=-8,shms_theta=9.24,hms_p=4.17,hms_theta=29.41,
daq crashed at 18:34
20:28 Oct 1st, SHMS rotated to 10.77, HMS to 31.73
shms_p=-8,shms_theta=10.77,hms_p=3.76,hms_theta=31.73,
subrun 00-01: SHMS=26, Carbon hole + LH2
subrun 02-23: SHMS=26deg, LH2
subrun 24: SHMS=26deg, LH2 + carbon target
subrun 25: SHMS=26deg, Carbon
subrun 26: SHMS=26deg, carbon + SHMS=9.24deg LH2 target
subrun 27-42: shms_theta=9.24, LH23353 production, 22:35 Oct 1st - 23:01 Oct 1st, daq crashed at about 22:55
target=LH2, shms_p=-8,shms_theta=10.77,hms_p=3.76,hms_theta=31.73,
22:38 Oct 1st, SHMS rotated to 16.55, HMS to 29.4
target=LH2, shms_p=-8,shms_theta=16.55,hms_p=4.17,hms_theta=29.4, daq rate=7kHz
3354 production, 23:02 Oct 1st - 23:40 OCt 1st,
target=LH2, shms_p=-8,shms_theta=16.55,hms_p=4.17,hms_theta=29.4, daq rate=7kHz
23:25 target changed to dummy
target=dummy, shms_p=-8,shms_theta=16.55,hms_p=4.17,hms_theta=29.4, daq rate=6.7kHz
3355 production, 23:42 Oct 1st - 20:43 Oct 2nd
target=dummy, shms_p=-8,shms_theta=16.55,hms_p=4.17,hms_theta=29.4, daq rate=2.4kHz
23:55 Oct 1st, SHMS rotated to 15.09deg
00:15 Oct 2nd, target change to LH2
target=LH2,shms_p=-8,shms_theta=15.09,hms_p=3.77,hms_theta=31.72,
00:51 Oct 2nd, SHMS rotated to 13.67deg
01:07 Oct 2nd, target change to dummy
target=dummy,shms_p=-8,shms_theta=13.67,hms_p=3.35,hms_theta=34.36,
01:37 Oct 2nd, SHMS rotated to 12.24deg
target=dummy,shms_p=-8,shms_theta=12.24,hms_p=2.94,hms_theta=37.37,
02:08 Oct 2nd,target changed to LH2
02:25 Oct 2nd, SHMS rotated to 10.78deg
target=LH2,shms_p=-8,shms_theta=10.78,hms_p=2.51,hms_theta=40.97,
02:57 Oct 2nd,target changed to dummy
03:25 Oct 2nd, SHMS rotated to 9.25deg
target=dummy,shms_p=-8,shms_theta=9.25,hms_p=2.08,hms_theta=45.36,
03:42 Oct 2nd,target changed to LH2
04:30 Oct 2nd, SHMS rotated to 26.02deg
target=LH2,shms_p=-4.935,shms_theta=26.02,hms_p=6.476,hms_theta=19.55,
12:29 Oct 2nd,target changed to dummy
13:30 Oct 2nd, SHMS rotated to 20.02deg
target=dummy,shms_p=-6.286,shms_theta=20.02,hms_p=5.107,hms_theta=24.91,
14:02 Oct 2nd,target changed to LH2
15:30 Oct 2nd, SHMS rotated to 15.01deg
target=LH2,shms_p=-7.626,shms_theta=15.01,hms_p=3.738,hms_theta=31.89,
16:05 Oct 2nd,target changed to dummy
16:30 Oct 2nd, SHMS rotated to 10.02deg
target=dummy,shms_p=-9.005,shms_theta=10.02,hms_p=2.289,hms_theta=43.13,
17:55 Oct 2nd,target changed to LH2
18:40 Oct 2nd, SHMS rotated to 10.02deg
target=LH2,shms_p=-9.2,shms_theta=9.26,hms_p=2.076,hms_theta=45.39,
19:05 Oct 2nd,target changed to dummy
19:35 Oct 2nd, SHMS rotated to 7.995deg
target=dummy,shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
21:30 Oct 2nd,target changed to LH2
21:54 Oct 2nd,SJMS sieve in
22:18 Oct 2nd,target changed to Beryllium,
target=Be,SHMS Sieve Slit in,shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
3356 production, 20:44 Oct 2nd - 17:05 Oct 3rd
target=dummy, shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
22:52 Oct 2nd,target changed to LH2
target=LH2,SHMS Sieve Slit in,shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
23:28 Oct 2nd,target changed to dummy, SHMS sieve still in
target=dummy,SHMS Sieve Slit in,shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
23:45 Oct 2nd, SHMS momentum set to -8.55
00:08 Oct 3rd,target changed to LH2
target=LH2,SHMS Sieve Slit in,shms_p=-8.55,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
00:49 Oct 3rd,target changed to Beryllium,
target=Beryllium,SHMS Sieve Slit in,shms_p=-8.55,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
01:28 Oct 3rd,target changed to LH2
01:42 roated SHMS and HMS. Spectrometer Emergency Stop Detected, Hall is open for trouble shooting.
beam stopped from 1:38.
Accelerator can not deliver beam since 04:10 Oct 3rd3357 production, 18:20 Oct 3rd - 12:14 Oct 4th
23:45 Oct 3rd, tune beam
target=LH2,shms_p=-4,shms_theta=20.02,hms_p=-4,hms_theta=20.0,
01:05 SHMS and HMS rotated to 25deg
target=LH2,shms_p=-3.5,shms_theta=25.02,hms_p=-3.5,hms_theta=25.0,
03:22 SHMS and HMS rotated to 25deg
target=LH2,shms_p=-2.5,shms_theta=35.02,hms_p=-2.5,hms_theta=35.0,
05:27 change momentum to 1.24GeV SHMS
target=LH2,shms_p=-1.24,shms_theta=35.02,hms_p=-2.5,hms_theta=35.0,
08:19 SHMS rotated to 8 deg, momentum is set to -9.2GeV
08:45 target changed to LD2
target=LD2,shms_p=-9.2,shms_theta=8,hms_p=-2.5,hms_theta=35.0,
08:45 target changed to C12
target=Carbon,shms_p=-9.2,shms_theta=8,hms_p=-2.5,hms_theta=35.0,
10:40 Beam is off3358 cosmic, 13:30 Oct 4th - 13:40 Oct 5th, no beam for the whole run
3359 cosmic, 13:42 Oct 5th - 13:49 Oct 6th, no beam for the whole run
3360 cosmic, 13:51 Oct 6th - 15:24 Oct 6th, no beam for the whole run
change TS#3 prescale factor to 13361 cosmic, 15:26 Oct 6th - 17:45 Oct 6th, no beam for the whole run
enable TS#4, which is VME DSC ELC output ch43362 production, 17:47 Oct 6th - 01:02 Oct 10th, no beam until 03:22 Oct 9th
03:28 Oct 9th, target changed to Aluminum Hole,shms_p=-9.2,shms_theta=8,hms_p=-1.95,hms_theta=25.99,
04:16 Oct 9th, Target changed to LD2,
04:45 Oct 9th, Target changed to carbon,
05:53 Oct 9th, Target changed to LD2,
07:46 Oct 9th, Target changed to Carbon,
09:16 Oct 9th, Target changed to LD2,
10:26 Oct 9th, Target changed to Carbon,
11:47 Oct 9th, SHMS rotated to 8.5deg
13:40 Oct 9th, Target changed to LD2,shms_p=-9.2,shms_theta=8.50,hms_p=-1.95,hms_theta=25.99,
15:18 Oct 9th, SHMS rotated to 26deg,shms_p=-1.95,shms_theta=26.00,hms_p=-1.95,hms_theta=25.99
15:55 Oct 9th, Target changed to LH2,
16:16 Oct 9th, Target changed to dummy,
17:36 Oct 9th, Target changed to Ca40,
19:00 Oct 9th, Target changed to Carbon,
beam stopped at 19:05 Oct 9th
3363 production, 01:02 Oct 10th - 18:23 Oct 10th
target=Carbon,,shms_p=-1.95,shms_theta=26.00,hms_p=-1.95,hms_theta=25.99
02:00 Oct 10th, Target changed to Dummy,
02:24 Oct 10th, Target changed to LD2,
02:51 Oct 10th, Target changed to LH2,
03:15 Oct 10th, both SHMS and HMS momenta changed to -5.42:
target=LH2,shms_p=-5.42,shms_theta=26.00,hms_p=-5.42,hms_theta=25.99
08:25 Oct 10th, Target changed to LD2,
17:18 Oct 10th, Target changed to Dummy,
3364 production, 18:24 Oct 10th - 14:52 Oct 11th
target=Dummy,shms_p=-5.42,shms_theta=26.00,hms_p=-5.42,hms_theta=25.99, daq rate 6.4kHz @60uA
19:25 Oct 10th, Target changed to Ca40,
21:46 Oct 10th, Target changed to Carbon,
00:45 both SHMS and HMS momenta changed to -4.767
target=Carbon,shms_p=-4.767,shms_theta=26.00,hms_p=-4.767,hms_theta=25.99
05:09 Oct 11th, Target changed to Ca40,
09:18 Oct 11th, Target changed to Dummy,
12:33 Oct 11th, Target changed to LD2,
13:49 Oct 11th, Target changed to LH2,
daq crashed at 06:07 Oct 11th
3365 production, 14:54 Oct 11th - 20:52 Oct 11th
target=LH2,shms_p=-4.767,shms_theta=26.00,hms_p=-4.767,hms_theta=25.99
16:45 both SHMS and HMS momenta changed to -4.19
target=LH2,shms_p=-4.19,shms_theta=26.00,hms_p=-4.19,hms_theta=25.99,
19:33 Oct 11th, Target changed to LD2,
3366 production, 20:58 Oct 11th - 13:28 Oct 13th
target=LH2,shms_p=-4.19,shms_theta=26.00,hms_p=-4.19,hms_theta=25.99, daq rate 6.7kHz@60uA
21:12 Oct 11th, Target changed to Dummy,
23:10 Oct 11th, Target changed to Ca40,
daq crashed at 21:32 Oct 11th
3367 pedestal, 13:32 Oct 13th - 13:44 Oct 13th,
target=Carbon, shms_p=2.52,shms_theta=26.00,hms_p=2.52,hms_theta=25.99,
13:38 target changed to dummy
daq crashed
3368 production, 13:45 Oct 13th - 14:22 Oct 13th
target=Dummy, shms_p=2.52,shms_theta=26.00,hms_p=2.52,hms_theta=25.99,
daq crashed
3369 production, 14:25 Oct 13th - 14:45 Oct 13th
target=Dummy, shms_p=2.52,shms_theta=26.00,hms_p=2.52,hms_theta=25.99, daq rate 6.2kHz@58uA
daq crashed
3370 production, 14:52 Oct 13th - 17:55 Oct 13th
14:53 target changed to LD2
target=LD2, shms_p=2.52,shms_theta=26.00,hms_p=2.52,hms_theta=25.99, daq rate 6.6kHz@58uA
15:24 target changed to LH2
16:12 target changed to Ca40
16:15 both SHMS and HMS momenta changed to -2.21
target=Ca40, shms_p=2.21,shms_theta=26.00,hms_p=2.21,hms_theta=25.99,
17:05 target changed to Carbon
3371 production, 17:55 Oct 13th - 23:59 Oct 13th
target=Carbon, shms_p=2.21,shms_theta=26.00,hms_p=2.21,hms_theta=25.99, daq rate 6.7kHz@60uA
18:35 target changed to Ca40
19:29 both SHMS and HMS momenta changed to 1.95 GeV/c
target=Ca40, shms_p=1.95,shms_theta=26.00,hms_p=1.95,hms_theta=25.99
20:15 target changed to Carbon @60uA
21:14 target changed to dummy @40uA
21:46 target changed to Loop2 LH2
22:18 target changed to Loop1 LD2 @60uA
beam stopped at 22:45 to rotated spectrometers, but failed. SO no beam until 01:30 Oct 14th.
3372 production, 23:59 Oct 13th - 15:02 Oct 14th
01:20 SHMS rotated to 8 deg, HMS to 20deg
no beam until 01:30
target=LD2, shms_p=9.2,shms_theta=8.00,hms_p=3.4,hms_theta=20
01:59 target changed to Carbon
02:24 target changed to Ca40
03:34 target changed to Carbon
04:04 target changed to Loop1 LD2
04:33 HMS momentum changed to 2.71 GeV/c
04:43 target changed to Loop2 LH2
target=LH2, shms_p=9.2,shms_theta=8.00,hms_p=2.71,hms_theta=20
04:58 target changed to Carbon
05:26 target changed to Ca40
06:02 HMS momentum changed to 2.421 GeV/c
target=Ca40, shms_p=9.2,shms_theta=8.00,hms_p=2.421,hms_theta=20
06:26 target changed to Beryllium
06:54 target changed to dummy
07:22 target changed to Loop2 LH2
beam stopped at 8 AM
3373 production, 15:03 Oct 14th - 02:16 Oct 15th
beam came back at 15:45
target=LH2, shms_p=9.2,shms_theta=8.00,hms_p=2.421,hms_theta=20
16:05 target changed to Loop1 LD2
daq crashed at 18:35 Oct 14th due to disk is full
3374 trash, 02:18 Oct 15th - daq could not start
3375 trash, 02:22 Oct 15th - daq could not start
3376 production, 02:28 Oct 15th - 16:48 Oct 15th
target=tin foil (Sn), shms_p=9.2,shms_theta=8.00,hms_p=2.421,hms_theta=20
daq rate 6.4kHz @ 40uA
02:34 target changed to Ti foil
03:02 target changed to Fe foil
05:02 target changed to Ag foil
05:32 target changed to Th foil
06:03 target changed to Ni-58 foil
06:38 target changed to Ni-64 foil
beam stopped from 07:02 until 08:36
07:02 both SHMS and HMS change polarity to negative
07:32 target changed to Loop1 LD2
08:36 beam back: target=LD2, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20
daq crashed at 14:14 Oct 15th due to disk is full3377 trash, 17:20 Oct 15th - daq could not start
3378 production, 17:21 Oct 15th - 13:55 Oct 16th
17:21 target=Beryllium, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 6.6kHz @ 59uA
18:06 target changed to Ca40
daq crashed sincd 05:42, no beam since 08:55 Oct 16th
06:15 target changed to Ca48
3379 production, 17:58 Oct 16th - 15:26 Oct 17th
09:40 beam came back
target=Ca48, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
daq crashed since 12:47,
13:08 target changed to Carbon
3380 production, 15:29 Oct 17th - 00:45 Oct 18th
target=Carbon, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
21:38 target changed to B4C-11 (Boron-11)
daq crashed @ 22:45
00:15 target changed to B4C-10 (B-10)
3381 production, 00:47 Oct 18th - 00:34 Oct 19th
target=B4C-10, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 4.94kHz @59 uA
03:07 target changed to Sn foil
no beam since 03:27 till 19:41
19:41-19:57 HallC is doing BCM calibration
19:58 target=Sn, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
00:13 Oct 19th, target changed to Ti foil
3382 production, 00:34 Oct 19th - 13:37 Oct 19th
target=Ti foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
04:54 target changed to Fe foil
no beam since 08:00
3383 production, 23:54 Oct 19th - 10:59 Oct 20th
no beam until 02:00
target=Fe foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
02:40 target changed to Ag foil
04:17 target changed to Th foil
08:39 target changed to Ni-58 foil
10:58 target=Ni-58 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1250Hz @ 45uA
3384 production, 11:00 Oct 20th - 14:56 Oct 21st
11:02 target=Ni-58 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1250Hz 45uA 50uA
12:12 target changed to Ni-64 foil
18:51 target moved to home
20:13 target changed to Ni-64 foil
20:20 target=Ni-64 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1500Hz
22:20 target changed to Ni-58 foil
01:08 target changed to Th foil 60uA 50uA
02:59 target changed to Ag foil
04:56 target changed to Fe foil
07:23 target changed to Ti foil
09:38 target changed to Sn foil
11:05 target changed to B4C-10 foil
13:25 target changed to B4C-11 foil
14:51 target=B4C-11 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 2964Hz
3385 production, 11:00 Oct 21st - 14:14 Oct 22nd
14:57 target=B4C-11 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 2964Hz 50uA 30uA
15:14 target changed to Carbon foil
00:20 target changed to Ca48 foil
02:15 target changed to Ca40 foil
04:33 target changed to Beryllium foil
05:33 target changed to dummy
08:51 target changed to Loop2 LH2
11:04 target changed to Loop1 LD2
14:14 target=LD2, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 4.2KHz
3386 production, 14:14 Oct 22nd - 04:04 Oct 23rd
14:14 target=LD2, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 4.2KHz @ 30uA
18:24 target changed to Loop2 LH2
19:12 target changed to dummy
19:38 target changed to Beryllium
20:19 target changed to Ca40
00:25 target changed to Ca48
daq crashed at 01:43 Oct 23rd
03:36 target changed to Carbon
3387 production, 04:07 Oct 23rd - 15:11 Oct 23rd
04:08 target=Carbon, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 3.0KHz @ 58.5 uA
07:18 target changed to B4C-11 foil
09:13 target changed to B4C-10 foil
11:57 target changed to Sn foil
13:41 target changed to Ti foil
3388 production, 15:11 Oct 23rd - 10:38 Oct 24th
15:12 target=Ti foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1235Hz 40uA 59uA
17:04 target changed to Fe foil
19:33 target changed to Ag foil
20:50 target changed to Th foil (Thorium)
00:34 target=Th foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 4.7kHz
01:22 target changed to Ni-58 foil
08:33 target changed to Ni-64 foil
10:37 target=Ni-64 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1482Hz @ 50uA
3389 production, 10:39 Oct 24 - 15:09 Oct 24th
10:39 target=Ni-64 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1482Hz @ 50uA
12:08 HMS momentum changed to -4.78 GeV/c
target=Ni-64 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20,
13:28 target changed to Ni-58 foil
3390 production, 15:09 Oct 24 - 17:20 Oct 24th
target=Ni-58 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20,
15:50 target changed to Th foil
16:57 target changed to Ag foil
17:19 target=Ag foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20, daq rate 4.2kHz @ 45uA
Name: SC0_T, SC0_B, SC1_T, SC1_B,
HV: 1700 1700 1780 1850
3391 production, 17:31 Oct 24 - 15:12 Oct 25th
17:19 target=Ag foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20,
17:36 target changed to Fe foil
17:50 target=Fe foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20, daq rate 3.5kHz 45uA 46.5uA
18:26 target changed to Ti foil
19:20 target=Ti foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20, daq rate 2.7kHz
20:56 target changed to B4C-11 foil
21:51 target changed to Carbon foil
00:04 target changed to Ca48 foil
01:21 target changed to Ca40 foil
03:11 target changed to Beryllium foil
03:46 target changed to dummy
03:59 target changed to LH2
06:09 target changed to LD2
07:55 target changed to LH2
08:13 target changed to dummy
08:28 target changed to Beryllium foil
08:43 target changed to Ca40 foil
09:39 target changed to Ca48 foil
10:11 target changed to Carbon foil
11:11 target changed to B4C-11 foil
12:10 target changed to B4C-10 foil
12:32 target changed to Sn foil
12:48 target changed to Ti foil
13:16 target changed to Fe foil
13:42 target changed to Ag foil
beam stopped at 14:15
3392 production, 15:25 Oct 25 - 13:52 Oct 26th
target=Ag foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20
15:28 target changed to Th foil
18:09 target changed to Ag foil
18:15 target=Ag foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20, daq rate 6.7kHz @ 46uA
19:08 target changed to B4C-10 foil
daq crashed at 19:31
19:39 target changed to B4C-11 foil
...
13:22 target changed to Ca40 foil
3393 production, 13:55 Oct 26 - 04:10 Oct 27th
accelerator can not delieve beam until ?
target=Ca40 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-2.71,hms_theta=20, daq rate 6.7kHz @ 46uA
coda crashed at 02:55
3394 production, 04:15 Oct 27 - 08:03 Oct 27th
04:16 target=LD2, shms_p=-9.2,shms_theta=8.00,hms_p=-2.42,hms_theta=20, daq rate 6.7kHz @ 30uA
remove VTP board
MaROC function added into read-out-list
3395-3430 trash, daq test
add epics variable: target ladder encoder hcBDSPOS SHMS changed to 10deg, HMS to 35 deg, spectrometer polarity changed to positive target changed3431 pedestal, 21:01 Oct 27th - 21:04 Oct 27th
3432 production, 21:06 Oct 27th - 20:32 Oct 28th
target=Carbon, shms_p=+9.2,shms_theta=10.00,hms_p=+2.11,hms_theta=35,
00:28 target changed to Ca40 foil
beam stopped at 0:44
3433 production, 20:33 Oct 28th - 12:40 Oct 29th
beam came back at 00:49, target at home
00:49 target=home, shms_p=+9.2,shms_theta=10.00,hms_p=+2.11,hms_theta=35,
01:19 target changed to Carbon hole
01:22 target changed to Ca40 foil
02:16 target changed to Loop1 LD2
03:49 target changed to Loop2 LH2
04:31 target changed to dummy
05:02 target changed to Ca40 foil
05:37 target changed to Carbon foil
07:14 target changed to Ca40 foil
08:01 target changed to dummy
08:37 target changed to Loop2 LH2
09:06 target changed to Loop1 LD2
coda crashed at 12:30 due to disk is full
3434 production, 12:43 Oct 29th - 14:47 Oct 30th
13:00 target=LD2, shms_p=+9.2,shms_theta=10.00,hms_p=+1.44,hms_theta=35, daq rate=6.7kHz @40uA
14:43 target changed to Loop2 LH2
17:17 target changed to dummy
18:49 target changed to Loop2 LH2
19:14 target changed to dummy
19:55 target changed to Ca40
20:49 target changed to Carbon
coda crashed at 21:25
22:59 HMS momentum changed to +1.26
target=Carbon, shms_p=+9.2,shms_theta=10.00,hms_p=+1.26,hms_theta=35,
23:55 target changed to Ca40
...3435 production, 14:50 Oct 30th - 02:10 Oct 31st
15:00 target=Ca40, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @50uA
3436 production, 02:10 Oct 31st - 13:30 Oct 31st
02:10 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @50uA
04:30 MPOD HV crate was tripped off
3437 production, 13:37 Oct 31st - 13:54 Oct 31st
13:40 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
comparing to run 3436, it seems that 6.7kHz is the maximum daq rate.
I plan to change the prescale factor to confirm this.
3438 production, 13:56 Oct 31st - 14:02 Oct 31st
13:58 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
3439 production, 14:04 Oct 31st - 14:06 Oct 31st
14:05 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
3440 production, 14:09 Oct 31st - 14 Oct 31st
14:10 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
3441 production, 14:09 Oct 31st - 14:11 Oct 31st
14:10 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=235Hz @60uA
3442 production, 14:21 Oct 31st - 14:24 Oct 31st
14:22 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=2.6kHz @60uA Enable TS#1, TS#2 and TS#3 change TS#3 prescale factor from 10 to 5
3443 trash, daq could not start Enable TS#1, TS#2 and TS#3 change TS#3 prescale factor from 5 to 4
3444 production, 14:31 Oct 31st - 14:34 Oct 31st
14:32 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA Enable TS#1, TS#2 and TS#3 change TS#3 prescale factor from 4 to 6
3435 trash, daq could not start
3446 production, 14:38 Oct 31st - 14:40 Oct 31st
14:39 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=4.8kHz @60uA
3447 production, 14:43 Oct 31st - 14:50 Oct 31st
14:45 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.6kHz @60uA
3448 trash, daq could not start
3449 production, 14:58 Oct 31st - 23:36 Oct 31st
14:59 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=4.8kHz @60uA
16:09 target changed to Carbon
3450 production, 23:37 Oct 31st - 11:14 Nov 1st
23:39 target=Carbon, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=1.7kHz @55.5uA
03:53 target changed to LD2
04:00 SHMS and HMS momentum changed to -4.0GeV/c, HMS rotated to 20.7deg
target=LD2, shms_p=-4.0,shms_theta=10.00,hms_p=-4.0,hms_theta=20.7
06:35 SHMS and HMS rotated to 20.deg
target=LD2, shms_p=-4.0,shms_theta=20.0,hms_p=-4.0,hms_theta=20.0
beam was off since 09:15
3451 pedestal, 11:15 Nov 1st, no beam
3452 production, 17:40 Nov 1st - 17:47 Nov 1st
target=LD2, shms_p=-4.0,shms_theta=20.0,hms_p=-4.0,hms_theta=20.0, daq rate 6.67kHz @ 50uA
3453 production, 17:50 Nov 1st - 00:52 Nov 2nd
target=LD2, shms_p=-4.0,shms_theta=20.0,hms_p=-4.0,hms_theta=20.0, daq rate 5.1kHz @ 50uA
3454 production, 00:53 Nov 1st - 09:15 Nov 2nd
target=dummy, shms_p=-4.0,shms_theta=20.0,hms_p=-4.0,hms_theta=20.0, daq rate 741Hz @ 10uA
3455 pedestal, 18:28 - checking the DAQ after dorking with the maroc readout, no beam
3456 production, 18:43 Nov 2nd - 01:00 Nov 3rd
daq machine died at 01:00
======================================================
daq machine tunl11 is dead
new daq mahine uvasolid is up ...
======================================================
3457-3458 trash, debug daq
3459 pedestal, 22:30 Nov 11th - 21:34 Nov 11th, no beam
3460 production, 22:30 Nov 11th, - 15:49 Nov 12th
target=LD2, shms_p=-9.2,shms_theta=9.85,hms_p=-2.72,hms_theta=35.01, daq rate 3.0kHz @60uA
3461 production, 15:41 Nov 12th, - 16:00 Nov 13rd
target=Ca40, shms_p=-9.2,shms_theta=9.85,hms_p=-2.72,hms_theta=35.01, daq rate 2.5kHz @50uA
coda stopped at 15:50 (uvasolid reboot?)
3462 trash, 03:01 Nov 14th, - 03:45 Nov 14th
target=Beryllium, shms_p=-9.2,shms_theta=9.85,hms_p=-2.4,hms_theta=35.01, daq rate 250Hz @50uA
MPOD HV board1 read back does not match set values......
3463 production, 03:47 Nov 14th, - 15:40 Nov 14th
target=Beryllium, shms_p=-9.2,shms_theta=9.85,hms_p=-2.4,hms_theta=35.01, daq rate 1.7kHz @50uA
MPOD board1 was tripped off, need to check from data when it happen
3464 production, 15:42 Nov 14th, - 04:00 Nov 15th
target=Ca40, shms_p=-9.2,shms_theta=9.85,hms_p=-2.4,hms_theta=35.01, daq rate 3kHz @55uA
3465 production, 04:06 Nov 15th, - 07:00 Nov 15th
target=Ca40, shms_p=-9.2,shms_theta=9.85,hms_p=-1.63,hms_theta=35.01
===================================================
3466 - 3529 trash, debug maroc-ssp daq
===================================================
SHMS at 20deg
3530 - 3533 trash, debug daq for prescale factor
change DAC values for fadc slot8.7 and slot8.9 in fadc config file # for TS#2 = Top_Shower & Top_PreShower#FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3170 3170 3440 3450 3470 3460 3450 3440 3390 # for TS#2 = Left_Shower & Left_PreShower
FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3470 3170 3140 3450 3470 3460 3450 3440 3390 determine prescale factors (from run 3534 to 3536), Finalize it from run 3537 Disable TS#1 and TS#3, only TS#2 is on, prescale_factor is 0
3534 production, 11:34 Nov 17th, - 11:46 Nov 17th
target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 4.5kHz @60uA
target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 3.8kHz @50uA
target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 3.1kHz @40uA Disable TS#1 and TS#2, only TS#3 is on, prescale_factor is 8
3535 production, 11:50 Nov 17th, - 11:56 Nov 17th
target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 270Hz @40uA Disable TS#2 and TS#3, only TS#1 is on, prescale_factor is 0
3536 production, 11:34 Nov 17th, - 11:46 Nov 17th
target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 2.7kHz @40uA
target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 2.0kHz @30uA Enable TS#1, S#2 and TS#3, prescale_factors are 0,1,5
3537 production, 12:05 Nov 17th, - 12:18 Nov 17th
target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 3.3kHz @30uA
3538 production, 12:20 Nov 17th, - 21:06 Nov 17th
target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 2.4kHz @20uA
14:56 target changed to LD2
target=LD2, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 5.7kHz @50uA
3539 trash, 21:08 Nov 17th, - 21:12 Nov 17th
no beam but got 7kHz daq rate, why .....?
3540 pedestal 21:15 Nov 17th, -21:17 Nov 17th, no beam
SHMS rotated to =26.41deg=
TS#2 changed from "Left_PreShower & Left_Shower" to "Right_PreShoer & Right_Shower"3541 trash 16:02 Nov 18th, -16:04 Nov 18th, no beam ,debug daq
changed FADC config file#FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3170 3170 3440 3450 3470 3460 3450 3440 3390 # for TS#2 = Left_Shower & Left_PreShower
#FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3470 3170 3140 3450 3470 3460 3450 3440 3390 # for TS#2 = Right_Shower & Right_PreShower
FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3170 3470 3140 3450 3470 3460 3450 3440 3390
3542 cosmic 16:11 Nov 18th, - 16:18 Nov 18th, no beam,
TS#1, TS#2 and TS#3 have prescale factors 0,1,5,first 100k are pulse trigger
3543 cosmic 16:19 Nov 18th, - ? Nov 18th, no beam,
TS#1, TS#2 and TS#3 have prescale factors 0,0,0, no pulse trigger, daq rate is 15Hz
3544 - 3552 trash, debug maroc daq
3553 production, 18:42 Nov 18th - 18:42 Nov 18th, daq rate ~7kHz
target=LH2, shms_p=-4.78,shms_theta=26.55,hms_p=-4.78,hms_theta=26.5, daq rate 7kHz @60uA
this run has no prescale factors
daq is saturated, I need to apply the prescale factor ....
3554 production, 18:42 Nov 18th - 13:12 Nov 19th
target=LH2, shms_p=-4.78,shms_theta=26.55,hms_p=-4.78,hms_theta=26.5, daq rate 4.6kHz @60uA
dummy target, daq rate 3.3kHz @ 40uAMPOD HV boards were both tripped off at around 12:003555 production, 13:14 Nov 19th - 03:37 Nov 20th
target=Ca48, shms_p=-9.2,shms_theta=8,hms_p=-2.72,hms_theta=35,
MPOD board2 read back values are zero for run 3556 and 3557, data mightnot be good
3556 production(? need to check data), 03:37 Nov 20th - 16:51 Nov 20th
target=LD2, shms_p=-9.2,shms_theta=8.13,hms_p=-4.08,hms_theta=35, daq rate 6.2kHz @30uA
3557 production?(need to check), 16:53 Nov 20th - 17:03 Nov 20th
target=LD2, shms_p=-9.2,shms_theta=8.13,hms_p=-4.08,hms_theta=35, daq rate 1.8kHz @30uA
MPOD board2 read back values are zero
= reboot MPOD crate
3558 production, 17:37 Nov 20th - 09:23 Nov 21st
target=LD2, shms_p=-9.2,shms_theta=8.13,hms_p=-4.08,hms_theta=35, daq rate 5kHz @30uA
09:20 ghost daq rate 3-5kHz @no beam
3559 pedestal, 09:27 Nov 21st - 09:43 Nov 21st, no beam
3560 production, 00:22 Nov 22nd - 12:35 Nov 22nd
target=LD2, shms_p=-9.2,shms_theta=8.13,hms_p=-4.08,hms_theta=35, daq rate 5.2kHz @60uA
3561 pedestal, 12:35 Nov 22nd - 12:40 Nov 22nd
no beam but daq rate ~5.2kHz @ 0uA, firmware bug
3562 pedestal, 12:45 Nov 22nd - 14:35 Nov 22nd
rol changed to solve ghost rate3563 production, 14:35 Nov 22nd - 14:40 Nov 22nd
target=dummy, shms_p=-3.57,shms_theta=34.46,hms_p=-3.57,hms_theta=34.28
3564 production, 14:42 Nov 22nd - 11:12 Nov 23rd
target=dummy, shms_p=-3.57,shms_theta=34.3,hms_p=-3.57,hms_theta=34.28
3565 pedestal, debug gem with pulse
3566-3567 trash
3568 pedestal, debug gem with pulse
3569-3570 pedestal, debug gem with pulse
3571 production, 23:22 Nov 23rd - ? Nov 24th
target=dummy, shms_p=-3.57,shms_theta=35.17,hms_p=-4.08,hms_theta=34.99, daq rate = 4kHz @40uA
00:50 coda crashed
3572 production, 13:24 Nov 24th - 00:41 Nov 25th
target=dummy, shms_p=-3.57,shms_theta=35.17,hms_p=-4.08,hms_theta=34.99, daq rate = 4kHz @40uA
MPOD were wtripped at 13:38
3573 pedestal, HVs are not on
3574 pedestal, HVs are not on
3575 production, 12:03 Nov 25th - 13:57 Nov 25th
target=B4C-11, shms_p=-9.2,shms_theta=8.66,hms_p=-3.09,hms_theta=34.99, daq rate = 3kHz @70uA
13:24 SHMS rotated to 11 deg
coda crashed at 13:30
3576 production, 13:59 Nov 25th - 15:06 Nov 25th
target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 3kHz @70uA
coda crashed at 14:36
3577 production, 15:08 Nov 25th - 15:22 Nov 25th
target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99
coda crashed at 15:15
3578 production, 15:24 Nov 25th - 16:48 Nov 25th
target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99
3579 production, 17:02 Nov 25th - 17:19 Nov 25th
target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 5kHz @70uA
3580 production, 17:21 Nov 25th - 21:16 Nov 25th
target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 5kHz @70uA
3581 production, 21:18 Nov 25th - 02:43 Nov 26th
target=B4C-10, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 4kHz @70uA
3582 production, 02:45 Nov 26th - ? Nov 26th - crashed ~3:17am
target=B4C-10, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 4kHz @70uA
3583 testrun after crash recovery
Updated rol to remote doOnce hack3584 production, 13:28 Nov 26th - 14:57 Nov 26th
target=B4C-10, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99
14:40 SHMS roated to 10 deg, HMS momentum changed to -2.72GeV/c
target=B4C-10, shms_p=-9.2,shms_theta=10.16,hms_p=-2.72,hms_theta=34.99
MPOD board1 HV was tripped off, it might affect run# 3582 - 3585
3585 production, 14:59 Nov 26th - 15:10 Nov 26th
target=B4C-10, shms_p=-9.2,shms_theta=10.16,hms_p=-2.72,hms_theta=34.99, daq rate 700Hz @ 70uA
3586 production, 15:13 Nov 26th - ? Nov 26th
target=B4C-10, shms_p=-9.2,shms_theta=10.16,hms_p=-2.72,hms_theta=34.99, daq rate 4kHz @ 70uA
17:57 coda crashed
3587 production, 04:36 Nov 27th - ? Nov 27th
06:13 coda crashed
3588 production, 13:40 Nov 27th - 00:31 Nov 28th
target=B4C-10, shms_p=-9.2,shms_theta=10.16,hms_p=-2.4,hms_theta=34.99, daq rate 4kHz @ 70uA
3589 production, 00:33 Nov 28th - 09:30 Nov 28th
target=Beryllium, shms_p=-9.2,shms_theta=10.16,hms_p=-4.08,hms_theta=34.99, daq rate 3.5kHz @ 60uA
coda stoped at 04:05 due to disk full.
7:20 beam is off.
3590 pedestal, 09:38 Nov 28th -10:03 Nov 28th, no beam
switched to config hallc_fadc_ssp_maroc3591 pedestal, 14:35 Nov 30th -14:35 Nov 30th, no beam, test maroc coda config
3592-3595 pedestal, test maroc coda config
switched back to config hallc_fadc_ssp=
3596 production, 13:18 Dec 3rd - 20:38 Nov 28th
3597-3599 trash, coda can not start
3600 production, 20:47 Dec 3rd - ? Nov 28th
coda crashed at 21:12. Mpod board2 crashed.
3601-3603 trash, coda can not start switched to config hallc_fadc_ssp_maroc
3604-3607 trash, coda can not start
reboot vme crate switched to config hallc_maroc3608-3617 trash, coda can not start 20221207 12:20 reboot MPD and LV of GEM
3618-3621 debug maroc coda
MPOD board1 tripped, it affects runs 3608-3621, reboot MPOD board1 = reconnect daq for high rate triggers, fadc config file changed ===set all prescale to zero. GEM HVs are connected to mpod board1
FADC slot7 DAC set to 3300
FADC250_DAC 3300
SC0 top and SC1 top were delayed by 32ns
3622-3623 trash, debug daq,
slot7:
FADC250_ALLCH_DAC 3310 3280 3280 3300 3150 3140 3150 3150 3280 3320 3450 3190 3140 3190 3130 3450
slot8:
FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3320 3320 3290 3450 3470 3460 3150 3440 3390
3624 debug daq, data is useful but has latency issue, 01:26 Dec 14th - 10:40 Dec 14th
Cherenkov sum is 40ns earlier than shower sum, SC0_top and SC1_top is 6ns earlier than shower sum after 32ns delay
N625 FIFO will introduce 8-10 ns of delay.
shower sum also connected to vmeDSC ch#4, whose 4th twist pin is connected to TS#4 in TI
3625 production 19:28 Dec 14th - 19:36 Dec 14th
change FADC slot7.15 DAC value from 3450 to 3310slot7: FADC250_ALLCH_DAC 3310 3280 3280 3300 3150 3140 3150 3150 3280 3320 3450 3190 3140 3190 3130 3310
3626 production 19:39 Dec 14th - 23:57 Dec 14th
3627 production 00:00 Dec 15th - 11:15 Dec 15th
3628 production 13:19 Dec 15th - 23:41 Dec 15th
updated rol: TS#4 only, no pulse triggers3629 trash, 23:43 Dec 15th - 23:45 Dec 15th
debug vmeDSC, does not work
Note that TS#4 is still not working, although TS#4 prescale factor is set to 5
3630 production 23:50 Dec 15th - 10:41 Dec 16th
03:59 DISK is full, it might affect subrun 27-40
3631 production 10:46 Dec 16th - 19:20 Dec 16th
14:35 target=dummy, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 735Hz @40uA
3632 production 19:50 Dec 16th - 04:23 Dec 17th
no beam at the beginning
00:58 target=Beryllium, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 3.2kHz @60uA
Livetime went to zero as soon as I took a look.
3633 test to make sure daq still ok.
took some pedestal
3634-3670 trash, no data files ====================================================================================================
Moving DAQ to uvasolid2 - Bryan... 17dec2022 - 4:30am
3671 production, 04:33 Dec 17th - 13:15 Dec 17th
3672 production 13:19 Dec 17th - 13:24 Dec 17th
only TS#4 is enabled, disabled internal pulse triggers3673 debug TS#4,trash, 13:35 Dec 17th - 13:37 Dec 17th
TS#4 is not working yet, daq rate = 0 @ 40uA
3674 debug TS#3,trash, 13:40 Dec 17th - 13:49 Dec 17th
TS#3 is not working yet,, daq rate = 1~2Hz @ 40uA
3675 production, 13:52 Dec 17th - 14:09 Dec 17th
14:08 target=He-3, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 490Hz @40uA
3676 production, 14:11 Dec 17th - 14:15 Dec 17th
14:12 target=He-3, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 245Hz @40uA
3677 production, 14:17 Dec 17th - 22:22 Dec 17th
no beam for the first 100k pulse triggers. Maximum daq rate 6860Hz
14:20 target=He-3, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 735Hz @40uA
updated sbsvme22 to use uvasolid2 - 22:22 Dec 173678 production, 22:45 Dec 17th - 01:31 Dec 18th
beam stop at 23:56
3679 production, 01:41 Dec 18th - 15:32 Dec 18th
no beam for the first 100k pulse triggers.
3680 production, 15:34 Dec 18th - 00:00 Dec 19th
15:35 target=Ca-40, shms_p=-9.2,shms_theta=8.5,hms_p=-3.57,hms_theta=34.99, daq rate = 4.4kHz 60uA 60uA
20:45 target = Beryllium, daq rate = 3kHz
23:58 target = He-4 10cm, daq rate = 2.7kHz @ 40uA
3681 production, 00:01 Dec 19th - 09:47 Dec 19th
00:02 target=He-4 10cm, shms_p=-9.2,shms_theta=8.5,hms_p=-3.57,hms_theta=34.99, daq rate = 2.7kHz 40uA 40uA
00:06 change target to dummy, daq rate = 1.2kHz
beam stopped at 7:20. Happy wnter break!!!
3682 cosmic, first 100k events are internal pulse trigger
===================================================================
3683 cosmic, first 100k events are internal pulse trigger
=====================================================================
Hall C cosmic test. Ecal is vertically placed. From the top to the bottom,
it is SC_top, GEM, Shower, PreShower, SC_bottom.
Led is placed inside the Cherenkov tank, driven by a 1kHz retangular wave (2,5V, 100ns width).
Trigger: TS#1 is the 1kHz retangular pulse, TS#2=SC_top & Shower_Sum & SC_bottom
TS#4 is Shower_sum using vmeDSC, prescale factor 5.
config = hallc_fadc_ssp_maroc
3695 good maroc debug data
3696-3707 trash, debug coda
3708-3709 hallc_fadc_ssp
3710 hallc_fadc_ssp_maroc
3711 hallc_fadc_ssp_maroc
3712 TS#2 only
bottom 5x10cm sc (117) goes to fadc8.3
sc light guide only (102) goes to fadc8.5
sc 2 inches x 3 inches (540) goes to fadc8.1
bottom SC fadc8.0
top SC fadc8.2
3745 TS#2 only, good data
3746-3762 debug daq
3784 cosmic production, 03:18 Dec 23rd - 11:43 Dec 23rd
TS#2(SC_top(5mv) & SC_bottom(5mv)) and TS#4(Shower_Sum(5mv)),good data
Add 2 more SC:
pershower tile just above the GEM, connected to signal lable 448(goes to FADC8.4), Hv cable 252
2inch by 2inch by 8inch SC was placed on top of preshower, connected to signal lable 538(goes to FADC8.6), Hv cable 249
vmeDSC(start from 1):
1(SC_bottom), 2(SC_top), 3(Shower_sum,not_use), 4(shower_sum goes to TS#4),...,
7(preshower_sum_not_use),8(SC_kedi6_tile)
TS#2 is "SC_top(5mv) & SC_bottom(5mv)", TS#3 is "SC_top(5mv) & SC_tile(5mv)", TS#4 is "Shower_Sum(5mv)"
3785 junk
3786 cosmic production, 14:55 Dec 23rd - 18:26 Dec 23rd,
no GEM, TS#234
3787 cosmic production, 18:29 Dec 23rd- 01:06 Dec 24th,
with GEM, TS#234
3788 cosmic production, 01:10 Dec 24th - 09:16 Dec 24th
3789 cosmic production, 09:17 Dec 24th -16:53 Dec 24th
3790 cosmic production, 16:53 Dec 24th - 00:13 Dec 25th
3791 cosmic production, 00:14 Dec 25th - 09:23 Dec 25th
3792 cosmic production, 09:24 Dec 25th - 11:28 Dec 25th
3793 cosmic production, 12:01 Dec 25th - 12:08 Dec 25th
3794 cosmic production, 12:13 Dec 25th - 15:58 Dec 25th
3795 cosmic production, 16:04 Dec 25th - 23:55 Dec 25th
3796 cosmic production, 23:57 Dec 25th - 09:27 Dec 26th
3797 cosmic production, 09:38 Dec 26th - 16:59 Dec 26th
3798 cosmic production, 16:59 Dec 26th - 00:08 Dec 27th
3799 cosmic production, 00:08 Dec 27th - 10:30 Dec 27th
3804 cosmic production, 12:00 Dec 27th - 16:37 Dec 27th
3806 cosmic production, 16:48 Dec 27th - 09:47 Dec 28th
3808 cosmic production, 10:57 Dec 28th - 08:51 Dec 29th
3812 cosmic production. 10:00 Dec 29th - 16:19 Dec 29th
3813-3821 Cherenkov LED run
FADC will record 100 samples from run 38223822 cosmic production. 00:30 Dec 30th - 00:56 Dec 30th
3832 cosmic production. 03:00 Dec 30th - 10:04 Dec 30th
swap preshower left and right
3852 cosmic production, but shower blocks are still has 120 deg rotation
rotate the shower blocks by 120deg
old: top(SDU#4), right(SDU#5), left(THU#2)
new: top(SDU#5), right(THU#2), left(SDU#4) This is the same as beamtest
3861-3862 Cherenkov LED run with raw sum
3863 cosmic production. 06:30 Dec 30th - 21:17 Dec 30th
HV scan for Cherenkov MaPMT3864-3867 Cherenkov LED run with raw sum GEM HV is off, Cherenkov HVs stay at -950V
3868 cosmic production. 22:04 Dec 30th - 12:49 Dec 31st
3871 Cherenkov LED run, 13:21 Dec 31st - 13:45 Dec 31st
3872 Cherenkov LED run, 13:47 Dec 31st - 15:47 Dec 31st
3873 cosmic production. 15:50 Dec 31st - 01:05 Jan 1st 2023
3874 cosmic production. 01:05 Jan 1st - 17:47 Jan 1st 2023
3875 cosmic production. 17:48 Jan 1st - 15:30 Jan 2nd 2023
3876 cosmic production. 15:32 Jan 2nd - 0:09 Jan 3rd 2023
GEM HV is on3877 cosmic production. 00:09 Jan 3rd - 11:20 Jan 3rd 2023
3878 cosmic production. 11:21 Jan 3rd - 13:33 Jan 3rd 2023
slot7 FADC delay by 40ns3879 cosmic production. 13:35 Jan 3rd - 13:37 Jan 3rd 2023 slot7 FADC delay by 160ns
3880 cosmic production. 13:40 Jan 3rd - 14:11 Jan 3rd 2023
-------------------------------------------------------------------
Cherenkov HVs change from 950,950,950,950 to 1050,1050,1100,1050
3881 cosmic production. 13:40 Jan 3rd - 14:48 Jan 3rd 2023
-------------------------------------------------------------------
change FADC slot8 delay
FADC250_ALLCH_DELAY 80 80 80 80 80 80 80 40 40 40 40 40 40 40 40 0
3882 cosmic production. 14:49 Jan 3rd - 17:56 Jan 3rd 2023
-------------------------------------------------------------------
HV changes: old: SC__top(1900), SC_bottom(1750), SC_E(1000)
New:
Name:_SC_top,_SC_bottom, ...,SC_E
HV:_____1800,______1850, ...,1100
3883 cosmic production. 14:49 Jan 3rd - 17:56 Jan 3rd 2023
3884 cosmic production. 17:57 Jan 3rd - 00:56 Jan 4th 2023
3885 cosmic production. 00:57 Jan 4th - 01:55 Jan 4th
HV changed for SC_bottom and shower_r and shower_l
old:
board1, 6kV, 8-ch:
Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
HV:__0,_3750,_0,_______________1640,_______________1800,_______________1550,_0,_0
board2, 2kV, 16-ch:
Name:_SC_top,_SC_bottom,_SC_B,_SC_C,___CerA,___CerB,___CerC,___CerD,_SC_A,_Shower_R(THU#2),_Shower_L(SDU#4),_Shower_T(SDU#5),__,__,_SC_E,_SC_D
HV:_____1800,______1850,_1700,_1600,___1050,___1050,___1100,___1050,_1600,____________1050,____________1030,_____________850,_0,_0,_1100,_1250
-------------------------------------------------
new:
board1, 6kV, 8-ch:
Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
HV:___0,_3750,_0,_______________1640,_______________1800,_______________1550,_0,_0
board2, 2kV, 16-ch:
Name:_SC_top,_SC_bottom,_SC_B,_SC_C,___CerA,___CerB,___CerC,___CerD,_SC_A,_Shower_R(THU#2),_Shower_L(SDU#4),_Shower_T(SDU#5),__,__,_SC_E,_SC_D
HV:_____1800,______1800,_1700,_1600,___1050,___1050,___1100,___1050,_1600,_____________950,_____________930,_____________850,_0,_0,_1100,_1250
-------------------------------------------------
3886 cosmic production. 01:56 Jan 4th - 08:07 Jan 4th
- ended to work on c1725
-------------------------------------------------------------------
Change HVs for Preshower_T(SDU#2), Preshower_L(SDU#1) and SC_Top
new:
Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
HV:___0,_3750,_0,_______________1750,_______________1800,_______________1600,_0,_0
board2, 2kV, 16-ch:
Name:_SC_top,_SC_bottom,_SC_B,_SC_C,___CerA,___CerB,___CerC,___CerD,_SC_A,_Shower_R(THU#2),_Shower_L(SDU#4),_Shower_T(SDU#5),__,__,_SC_E,_SC_D
HV:_____1850,______1750,_1700,_1600,___1050,___1050,___1100,___1050,_1600,_____________950,_____________930,_____________850,_0,_0,_1100,_1250
-------------------------------------------------
3887-3888 trash, HVs are off
3889 cosmic production. 16:06 Jan 4th - 19:21 Jan 4th
3890 cosmic production. 19:22 Jan 4th - 19:40 Jan 4th
-------------------------------------------------------------------
Change HVs for Preshower_T(SDU#2), Preshower_L(SDU#1) and Preshower_R(THU#1)
Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
HV:___0,_3750,_0,_______________1800,_______________1750,_______________1650,_0,_0
3891 cosmic production. 19:41 Jan 4th - 23:08 Jan 4th
GEM HV tripped during the run
3892 cosmic production. 23:09 Jan 4th - 23:45 Jan 4th
-------------------------------------------------------------------
Change HVs for Preshower_T(SDU#2) and Preshower_R(THU#1)
Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
HV:___0,_3750,_0,_______________1640,_______________1800,_______________1650,_0,_0
3893 cosmic production. 23:46 Jan 4th - 00:38 Jan 5th
3894 cosmic production. 00:39 Jan 5th - 00:54 Jan 5th
-------------------------------------------------------------------
Change HVs for Preshower_T(SDU#2) and Preshower_L(SDU#1)
Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
HV:___0,_3750,_0,_______________1800,_______________1800,_______________1550,_0,_0
3895 cosmic production. 00:54 Jan 5th - 08:38 Jan 5th
3896 trash
cosmic test for preshoweronly SC_top, SC_bottom, and 3 PreShowers are used. 3 PreShowers are stacked in one pile.
Trigger is "SC_top & SC_bottom"
----------------------------------------------------
Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
HV:____1850,_1750,_______________1640,_______________1800,_______________1550
hallc_fadc config
3897 cosmic production, SDU#2 does not connect well
3898 cosmic production, all works
hallc_fadc_ssp config
3899 cosmic production
3900 cosmic production, 21:35 Jan 5th - 23:25 Jan 5th
----------------------------------------------------
Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
HV:____1850,_1750,_______________1800,_______________1800,_______________1550
hallc_fadc config
3901 cosmic production, 23:27 Jan 5th - 00:22 Jan 6th
----------------------------------------------------
Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
HV:____1850,_1750,_______________1800,_______________1900,_______________1550
3902 cosmic production, 00:33 Jan 6th - 01:37 Jan 6th
----------------------------------------------------
Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
HV:____1850,_1750,_______________1900,_______________2000,_______________1650
3903 cosmic production, 01:37 Jan 6th - 02:34 Jan 6th
----------------------------------------------------
Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
HV:____1850,_1750,_______________1710,_______________1800,_______________1500
3904 cosmic production, 02:35 Jan 6th - 03:31 Jan 6th
----------------------------------------------------
Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
HV:____1850,_1750,_______________1730,_______________1800,_______________1515
3905 cosmic production, 03:35 Jan 6th - 07:36 Jan 6th
============================================================================Summary of preshower gain match cosmic test
run# _Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
3897-3900 _______1640,_______________1800,_______________1550
3901 _______1800,_______________1800,_______________1550
3902 _______1800,_______________1900,_______________1550
3903 _______1900,_______________2000,_______________1650
3904 _______1710,_______________1800,_______________1500
3905 _______1730,_______________1800,_______________1515 (best)
another predicted matched HVs: 1800, 1900, 1580
=======================================================
Updated by Jixie Zhang almost 2 years ago · 9 revisions