Project

General

Profile

Wiki » History » Version 12

Richard Trotta, 05/07/2018 01:28 PM

1 1 Richard Trotta
2 11 Richard Trotta
3 12 Richard Trotta
{{>toc}}
4 7 Richard Trotta
5 6 Richard Trotta
h1. *Notes from Meetings*
6 5 Richard Trotta
7 6 Richard Trotta
h2. February 22, 2018
8 1 Richard Trotta
 
9 4 Richard Trotta
*  Discussion of "Andres's":https://redmine.jlab.org/documents/19 slides on elastic W calculation in hcana - initial issue with negative W values seems to be due to outdated information in standard.kinematics file. Additional investigation ongoing.
10 2 Richard Trotta
* Brief description of Samip's work - working on coincidence timing decoding with JLab staff and re-optimization of kinematics
11 1 Richard Trotta
* Discussion of Richard's slides on run plan kinematics and preparations -
12
** everyone agrees that in general want to have as many L/T cross section separations as possible in a robust run plan balancing statistics vs. systematics
13
** before actual run may want to do a 3D optimization in all kinematic variables to get the best possible delta(epsilon) for the L/T separations
14
** for each setting will need 1-2 shifts for calibrations - need to negotiate with other experiments in run group
15
** kinematics plots W-Q2 show that still need to do some optimization
16
** run sheets: include raster size, update coincidence count labeling, and carbon target labeling
17
* Discussion of next meeting. Garth at JLab 8-16 March - might have meeting during that time.
18
19
20
* *Action Items:*
21
** Post slides/notes from this meeting and procedure to set up hcana in Redmine (Tanja)
22
** Update run sheet and kinematic optimization for W/Q2 (Garth)
23
** Circulate elastic calculations for kinematic settings (Samip)
24
** Continue investigation of elastic data and run plan kinematics (Andres/Richard)
25
** Test software installation instructions (Pete)
26
** Draft email to JLab management about need for small angle beam pipe - need to have HMS minimum angle of less than 13 degrees for kaon L/T separations (Tanja) 
27
28 8 Richard Trotta
h2. March 29, 2018
29 1 Richard Trotta
30
* Details of adding points to fall run plan - will be ready sooner, likely in week of 4/1 (Garth, Samip, Tanja)
31
* Luminosity scans (Ryan, Andres, "Richard":https://redmine.jlab.org/documents/16, Pete)
32
* Macros, SIDIS analysis (Hem, Anashe)
33
* Elastic data (TBD)
34 2 Richard Trotta
35
36 8 Richard Trotta
h2. April 26, 2018
37 2 Richard Trotta
38 3 Richard Trotta
* Discussion luminosity scan analysis (earlier scan) - "Richard":https://redmine.jlab.org/documents/18
39 2 Richard Trotta
** Shown is a scaler-based analysis using scalers from report file and from ROOT tree - the values are different, why that is has to be checked
40
** Notes on efficiencies in report file:
41
*** DT (EDTM) is not electronic deadtime. Instead use for now 50ns* trigger rate for HMS and 100ns* trigger rate for SHMS
42
*** Cherenkov efficiency seems low (check if that is due to PID, thresholds, pi/e, etc)
43
*** Tracking efficiency needs to be checked
44
*** 3/4 trigger efficiency seems ok
45
* Discussion luminosity scan analysis (later scan) - Ryan
46
** Fewer carbon runs than earlier scan
47
** Shown is a tracking-based analysis using data from the ROOT trees
48
** First results for carbon, LH2, and LD2, but efficiencies need to be checked
49
* SIDIS analysis - Hem
50
** Shown is a data/MC comparison for different kinematic settings. Agreement in shape is very good. Normalization has yet to be applied.
51
** Discussion about agreement in z and apparent offset - relation of this offset with spectrometer offset
52
* Analysis of exclusive events in SIDIS - Samip
53
** Shown is a look at the first kaon events in exclusive limit of SIDIS data
54
** Ongoing work on implementing coincidence time into tree
55
* Discussion of run plan, and in particular possible low Q2/low energy
56
** Assume that kaon low Q2=0.4 already included - have kinematics with specified beam energies, if needed
57 1 Richard Trotta
** For pion form factor and LT, have two possible settings that can use the prescribed beam energies: Q2=1.45 and 0.35 GeV2 - prioritize towards the higher Q2 as not as sensitive to offsets
58
** Garth will put this together in a draft email
59 8 Richard Trotta
60
h2. May 10, 2018
61 9 Richard Trotta
62
h1. BlueJeans Information
63
64 10 Richard Trotta
* Browser: https://bluejeans.com/7578012727
65
* Bluejeans app (https://www.bluejeans.com/downloads): "Join A Meeting" with Meeting ID: 7578012727 (no pass code required)
66
* Phone: 1-888-240-2560 (other numbers:  http://bluejeans.com/numbers)
67
** Participant code is 7578012727#