SoLID DAQ » SoLID ECal

h1. Fermilab Test Beam Run

h2. Run List 

beam hit the edge of top Ecal

New HV is: 1260, 1300, 920, 960, 940, 1940, 1780, 2100

Run 

777 First run - MWPC trigger -

New HV is: 1260, 1300, 920, 960, 940, 1840, 1680, 2000

783 Preshower channels set to 2V range in FADC

784 TS1 and TS2 - move detector position so beam is hitting the center of three ECals

785

New HV is: 1160, 1200, 820, 860, 840, 1840, 1680, 2000 

786 TS1 only - beam centered on calorimeter

New HV is: 1260, 1300, 820, 860, 840, 1740, 1580, 1900

787 lower HV on preshower

788

792

reduce 100 V more on preshower

793 short run PEB1 crashed

switch to FADC only config TiIntelvmeha8

795

Changing down stream Cerenkov N2 pressure

796 move to Top block

800 beam on the center of the top block, point A

801

802 beam on the center of the right block, point C

803 beam on the center of the left block, point A

804 beam on the center of 3 modules, 6.5k

805 2GeV, beam on the center of 3 modules, 31.7k

806 4GeV, beam on the center of 3 modules,

818 12 GeV e- 

819 12 GeV e- 

820 10 GeV e- 

821 8 GeV e-

822 6 GeV e-

===========1GeV===================

HV is: 1260, 1280, 760, 860, 880, 1640, 1480, 1800

823

824

825

Switch to TS2 trigger

828

Switch back to TS1

831

839 daq crashed

847 1 GeV

848 6 GeV

849 6 GeV

850 6 GeV

851 6 GeV

851 Cherenkov test DAQ run 

852 ??               

853 calibration run

854 calibration run

855 calibration run

856 calibration run

857 6 GeV

858 6 GeV

859 6 GeV

860 6 GeV

861 6 GeV

862 16 GeV

863 16 GeV

864 16 GeV

865 16 GeV

866 16 GeV

867 12 GeV

h2. Shifter Roles

* Leader: Communicate with MCR regarding desired beam energy and other relevant details.  Manage the DAQ (start and stop runs)

* Remote: Keep a shift log of actives during the shift.  Decode runs as they are completed. Post a shift summary logbook entry at the conclusion of your shift.

h2. VNC Connection Information (for Remote Shifts) 

* Using terminal, ssh into login and then the computer that has the VNC server on it

ssh -L 5901:localhost:XXXX @janedoe@fnalu.fnal.gov@

Replace XXXX with a port number of your choice (avoid 22). Log in using JLab CUE credentials

* In the same session, ssh to the computer: 

ssh -L XXXX:localhost:5901 @a-compton@clrlpc.dhcp.fnal.gov@ 

Log in using JLab CUE credentials for user a-compton.

* On your machine, run the VNC application. When prompted for the VNC Server, use: localhost:5901

Encryption: Let VNC Server choose

Enter password set up on the VNC server

Log in using JLab credentials

h2. How to make beam position plots using the MWPC data

The MWPC folder is located at: /home/a-compton/MWPC/

Raw data at: /home/a-compton/MWPC/data

decoder at: /home/a-compton/MWPC/analysis/basic

A script to run decoder and make one figure of beam position is available here:

/home/a-compton/MWPC/analysis/basic/wcsolid.csh

You can run this script at any folder.