Runlist » History » Version 27
Jixie Zhang, 01/17/2021 10:26 PM
1 | 8 | Jixie Zhang | 1. Runlist |
---|---|---|---|
2 | 1 | Alexandre Camsonne | |
3 | 8 | Jixie Zhang | beam hit the edge of top Ecal |
4 | New HV is: 1260, 1300, 920, 960, 940, 1940, 1780, 2100 |
||
5 | 27 | Jixie Zhang | |
6 | |||
7 | 1 | Alexandre Camsonne | 777 First run - MWPC trigger - |
8 | 8 | Jixie Zhang | |
9 | 27 | Jixie Zhang | 783 Preshower channels set to 2V range in FADC, new HV is: 1260, 1300, 920, 960, 940, 1840, 1680, 2000 |
10 | 8 | Jixie Zhang | |
11 | 784 TS1 and TS2 - move detector position so beam is hitting the center of three ECals |
||
12 | 27 | Jixie Zhang | |
13 | 785 New HV is: 1160, 1200, 820, 860, 840, 1840, 1680, 2000 |
||
14 | |||
15 | 7 | Alexandre Camsonne | 786 TS1 only - beam centered on calorimeter |
16 | 1 | Alexandre Camsonne | |
17 | 27 | Jixie Zhang | 787 lower HV on preshower, New HV is: 1260, 1300, 820, 860, 840, 1740, 1580, 1900 |
18 | 1 | Alexandre Camsonne | |
19 | 9 | Alexandre Camsonne | 788 |
20 | 1 | Alexandre Camsonne | |
21 | 792 |
||
22 | 9 | Alexandre Camsonne | |
23 | 27 | Jixie Zhang | 793 reduce 100 V more on preshower, New HV is: 1260, 1300, 820, 860, 840, 1640, 1480, 1800 |
24 | short run PEB1 crashed |
||
25 | 10 | Alexandre Camsonne | |
26 | 27 | Jixie Zhang | 795 switch to FADC only config TiIntelvmeha8 and use |
27 | 12 | Alexandre Camsonne | |
28 | Changing down stream Cerenkov N2 pressure |
||
29 | |||
30 | 27 | Jixie Zhang | ===========good data start from here=================== |
31 | |||
32 | 13 | Alexandre Camsonne | 796 move to Top block |
33 | 27 | Jixie Zhang | New HV: 1260, 1300, 880, 920, 940, 1640, 1440, 1800 |
34 | 797 |
||
35 | 16 | Alexandre Camsonne | |
36 | 27 | Jixie Zhang | 798 move to left block |
37 | 15 | Alexandre Camsonne | |
38 | 16 | Alexandre Camsonne | 800 beam on the center of the top block, point A |
39 | 15 | Alexandre Camsonne | 801 |
40 | 802 beam on the center of the right block, point C |
||
41 | |||
42 | 16 | Alexandre Camsonne | 803 beam on the center of the left block, point A |
43 | 1 | Alexandre Camsonne | |
44 | 16 | Alexandre Camsonne | 804 beam on the center of 3 modules, 6.5k |
45 | 15 | Alexandre Camsonne | |
46 | 16 | Alexandre Camsonne | 805 2GeV, beam on the center of 3 modules, 31.7k |
47 | |||
48 | 806 4GeV, beam on the center of 3 modules, |
||
49 | 17 | David Flay | |
50 | 818 12 GeV e- |
||
51 | 819 12 GeV e- |
||
52 | 820 10 GeV e- |
||
53 | 821 8 GeV e- |
||
54 | 822 6 GeV e- |
||
55 | 18 | Alexandre Camsonne | |
56 | 22 | Alexandre Camsonne | ===========1GeV=================== |
57 | HV is: 1260, 1280, 760, 860, 880, 1640, 1480, 1800 |
||
58 | 823 |
||
59 | 824 |
||
60 | 18 | Alexandre Camsonne | 825 |
61 | Switch to TS2 trigger |
||
62 | 19 | Alexandre Camsonne | |
63 | 828 |
||
64 | 20 | Alexandre Camsonne | |
65 | Switch back to TS1 |
||
66 | 21 | Alexandre Camsonne | |
67 | 831 |
||
68 | 23 | Jixie Zhang | |
69 | 839 daq crashed |
||
70 | 24 | David Flay | |
71 | 847 1 GeV |
||
72 | 25 | Jixie Zhang | ===========6GeV=================== |
73 | |||
74 | 24 | David Flay | 848 6 GeV |
75 | 849 6 GeV |
||
76 | 850 6 GeV |
||
77 | 851 6 GeV |
||
78 | 25 | Jixie Zhang | |
79 | 858 bad run |
||
80 | |||
81 | ===========16GeV=================== |
||
82 | 862, ecal HV is using 8GeV setting: 760, 860, 880 bad run, all saturated |
||
83 | 863, change ecal HV: 720, 820. 840, bad run, all saturated |
||
84 | 864 bad run, all saturated |
||
85 | 865, change ecal HV: 700 780,800 bad run, sdu#5 saturated |
||
86 | 866 bad run, sdu#5 saturated |
||
87 | ===========12GeV=================== |
||
88 | 867 |
||
89 | 26 | Jixie Zhang | 868 |
90 | 869 |
||
91 | |||
92 | 870 motion table moved to (1429,315) |
||
93 | 871 |
||
94 | |||
95 | 872 motion table moved to (1452,315) |
||
96 | 873 |
||
97 | 874 |
||
98 | |||
99 | 875 motion table moved to (1461,315) |
||
100 | 876 |
||
101 | |||
102 | 877 motion table moved to (1451,315) |