Version 9 - History - Hallc beamtest runlist - SoLID ECal - Redmine

Hallc beamtest runlist » History » Version 9

Jixie Zhang, 01/10/2023 08:35 PM

-Jixie Zhang
+#This file record the run list for solid ecal beamtest in HallC.
-Jixie Zhang
+#Do not delete
-Jixie Zhang
+-pass beam, 10.549 GeV
 =================================================================
-Jixie Zhang
+slot 7 FADC250_DAC 3300 (for all 16 channels)
 slot 8 FADC250_DAC 3300 (for all 16 channels)
 20220620 21:30
 HV slot  2:    0    0    0    0    0    0    0
 HV slot 10: 1500 1500 1500 1500    0    0    0    0    0    0    0
 	FADC only
 	FADC only
 	FADC only
 	FADC only
 	FADC only
 File not exist for run 2930-2949, debug DAQ
 20220621 12:20
 HV slot  2:  900  950  900    0    0    0    0
 HV slot 10: 1500 1500 1500 1500 1500 1500 1500 1800 1800 1800
 -2956	SSP only
 	SSP only, trash
 	debug DAQ, trash
 	First run for FADC+SSP, good data
 	good FADC+SSP data
 -2964    DEBUG SSP, all trash
 20220623 15:50
 HV slot  2:  900  950  900 1500 1500 1500 1500
 HV slot 10: 1600 1600 1700 1600 1500 1500 1500 1800 1800 1800
 From this run, trigger lost due to FIFO has an 100mv offset
 -2968	SSP only, no trigger and debug daq, trash
 	FADC+SSP, no trigger, trash
 	cosmic run, no trigger, trash
 beam run, no trigger, trash
 From run 2972, trigger is connected to another FIFO unit which has 0 offset
 20220624 12:20
 HV slot  2:  900  950  900 1000 1000 1000 1000
 HV slot 10: 1600 1600 1700 1600 1500 1500 1500 1800 1800 1800
 	debug DAQ, trash
 	good FADC+SSP data  <------- First run for good Cherenkov HV
 trash
 -2981	good FADC+SSP data
 	trash
 -3002	good FADC+SSP data
 -3005	debug DAQ, trash
 -3013	good FADC+SSP data
 -3015	cosmic
 		daq crash, no output files
 -3018	debug daq, trash
-Jixie Zhang
+		cosmic
-Jixie Zhang
+-3021	debug daq for DAC values and HV, trash
 =====================================================================
-Jixie Zhang
+GOOD DATA STARTED ......
-Jixie Zhang
+=====================================================================
-Jixie Zhang
+For all runs before 3022, slot 7 and slot 8 FADC250_DAC are 3300 for all channels. Therefore some channels might not see signal.
 20220629 16:20
 HV slot  2:  900  950  900 1000 1000 1000 1000
 HV slot 10: 1600 1600 1850 1750 1000 1100 1800 1680 1920 1800
 slot 8 FADC250_DAC 3000
 slot 8 FADC250_DAC 3300 3000 3300 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
 First production run  <-----------------
 DAQ crashed
 production
 debug run, cosmic, trash
 Jixie Zhang
-Jixie Zhang
+=====================================================================
-Jixie Zhang
+Cherenkov ch12 (started from 0) has cabling issue for runs before 3026
-Jixie Zhang
+=====================================================================
 Change FADC DAC for Ecal channels
 slot 8  FADC250_DAC 3300 3000 3300 3000 3000 3000 3000 3000 3000 3000 3300 3300 3300 3000 3300 3000
 production, cosmic at the first 4 hours(~30 events), see beam around 6 pm
 	production
 production
 	production, no beam at the beginning (several hours)
 	production
 	production
 	production
 	production
 	production
 	production
 	production
 	production, daq machine tunl11 has some issue and vncserver crashed, so coda also crashed
 	production, first test run after rebooting tunl11 and sbsvme22, data is good
 	production, test auto log scripts, data is good
 	production
 cosmic, trash
 	debug daq,trash
 no files, daq crashed
 FADC config file changed:
 ) remove slot 9
 ) slot 7
 FADC250_ALLCH_DAC 3205 3170 3170 3195 3195 3190 3200 3195 3180 3205 3190 3215 3170 3215 3175 3205
 )slot 8
 FADC250_W_WIDTH 400
 FADC250_ALLCH_DAC 3500 3200 3460 3190 3220 3210 3190 3220 3220 3190 3500 3520 3510 3500 3490 3450
 	cosmic, slot 8 FADC250_W_WIDTH 400
 	cosmic, slot 8 FADC250_W_WIDTH 400
-Jixie Zhang
+changed slot 7 FADC250_W_WIDTH from 200 to 400
 	both slot 7 and slot 8, FADC250_W_WIDTH = 400
 	production
-Jixie Zhang
+	production
 1 event only, cosmic, end it for changing config file
 ==============================================================
-Jixie Zhang
+:::::::::::::::::::::::USEFUL DATA START::::::::::::::::::::::
 Before run 3050, only part of the pulse was recorded, therefore all these runs are gabages.
 Runs 3050 - 3057 could be useful, but their HVs are not perfect.
 ==============================================================
 for both slot #7 and #8, changed to the following 2 lines:
-Jixie Zhang
+FADC250_W_OFFSET 1000
 FADC250_W_WIDTH 1000
 	debug fadc config file,FADC250_W_OFFSET=1000 and FADC250_W_WIDTH=1000
 	debug fadc config file,FADC250_W_OFFSET=1000 and FADC250_W_WIDTH=1000
 Jixie Zhang
-Jixie Zhang
+==============================================================
-Jixie Zhang
+for both slot #7 and #8, changed to the following 2 lines:
 FADC250_W_OFFSET 1060
 FADC250_W_WIDTH 400
 	debug fadc config file,FADC250_W_OFFSET=1060 and FADC250_W_WIDTH=400
 production
 production
-Jixie Zhang
+==============================================================
-Jixie Zhang
+HV changed
 Slot 2
-Jixie Zhang
+Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
 HV: 950 980 900 1000 1000 1000 1000
 Slot 10
 Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B, SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
 HV: 1600 1600 1750 1750 900 1000 1950 1580 1750 1750
-Jixie Zhang
+HV tripped, empty,trash
 production
 production
 ================================================================
-Jixie Zhang
+::::::::::::::::::::::::GOODEN DATA START:::::::::::::::::::::::
 ================================================================
-Jixie Zhang
+HV changed
 Slot 2
 Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
 HV: 1000 1030 900 1000 1000 1000 1000
 Slot 10
 Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B, SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
 HV: 1600 1600 1750 1750 880 1000 1950 1550 1800 1750
-Jixie Zhang
+production, 05:15 July 9th - 03:50, target=Loop 2 LH2,shms_p=8.035,shms_theta=7.83,hms_p=-2.398,hms_theta=28.19,
 :10 target changed to dummy, I=38uA,
 :43 target changed to Loop 2 LH2, I=38uA
 production, 03:56-15:24 July 10th,target=Loop 2 LH2,shms_p=8.035,shms_theta=7.83,hms_p=-2.398,hms_theta=28.19,
 production, 15:25-00:35, target=Loop 2 LH2,shms_p=8.035,shms_theta=7.83,hms_p=-2.398,hms_theta=28.19,
 production, 00:36-09:41 July 11th,target=Loop 2 LH2,shms_p=8.035,shms_theta=7.83,hms_p=-2.398,hms_theta=28.19,
 :55 SHMS rotated to 9.83deg, shms_p=8.035,shms_theta=9.83,hms_p=-2.398,hms_theta=28.19,
 production, 09:41-10:15 July 11th,target=Loop 2 LH2,shms_p=8.035,shms_theta=9.83,hms_p=-2.398,hms_theta=28.19,
-Jixie Zhang
+cosmic, 6 events
 Jixie Zhang
 :53 SHMS rotated to 5.65deg
 production, 16:06-11:19 July 12th,target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 production, 11:19-18:02 July 12th,target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 production, 18:02-00:43,target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 production, 00:45-11:48 July 13th,target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 production, 11:48-02:04, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 :15, target ladder moved to home, no target (absolute empty)
 :50, target changed to dummy
 :28, target changed to Loop 2 10cm LH2
 production, 02:04-09:54 July 14th, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 production, 09:55 July 14th - 10:16 July 15th, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 production, 10:16-03:26 July 15th, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 :38 target changed to dummy
 :33 target changed to Loop 2 LH2
 production, 03:27-16:39 July 16th, target=Loop 2 LH2,shms_p=8.035,shms_theta=5.65,hms_p=-2.398,hms_theta=28.19
 :29 SHMS rotated to 9.65deg, tried to get I=80uA
 production, 16:42-14:26 July 17th,target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
 production, 14:26-02:11,target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
 production, 02:11-10:35 July 18th,target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
 production, 10:16-00:39, target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
 production, 00:39-09:42 July 19th, target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
 :51 target changed to dummy
 production, 09:43-00:29 July 20th, target=dummy,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
 :04 target changed to Loop 2 LH2, target=Loop 2 LH2,shms_p=8.035,shms_theta=9.66,hms_p=-2.398,hms_theta=28.19
 :00-ish, SHMS rotated to 8.68deg, HMS rotated to 34.15deg,
 	target_type=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 	beam stopped at 19:00-ish, no beam for whole day of July 20th
 ===========================================================
-Jixie Zhang
+pulse trigger
 pulse trigger
 pulse trigger
 pulse trigger
-Jixie Zhang
+===========================================================
-Jixie Zhang
+-3084 trash, no data file
 debug daq
-Jixie Zhang
+production, 03:11-09:42 July 21st, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 09:43-16:07 July 21st, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 16:07-12:23 July 22nd, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 12:23-04:28 July 23rd, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 04:28-15:44 July 23rd, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 15:47-05:28 July 24th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 05:28-18:22 July 24th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 18:22-09:32 July 25th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 09:33-23:40 July 25th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 23:41-09:29 July 26th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 09:29-15:35,July 26th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 :45 target changed to dummy
 	beam stopped at ~15:10 due to thunderstorm.
 production, 15:35 July 26th - 04:56 July 28th, target=dummy,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 	Dummy target when this run was started. At 22:45 July 26, target ladder was changed to home(empty).
 	Tune beam cane at 11:27 July 27th.
 :15 July 27th, beam was stable to reach 65uA, changed target to Loop 2 LH2.
 	      target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15
 :06 July 27th, changed target to dummy.
 :06 July 27th, changed target to Loop 2 LH2.
 production, 04:56-09:48 July 28th, target=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15
 updating readout list ......
 Bryan added a feature to run the fixed pulser at some frequency until some number of sync events.
 It's currently configured (ti_list.c) with the structure:
 typedef struct
+{
   int enable;       // enable (1) / disable (0)
   int interval;     // 1 sync event every *interval* events
   int pedestal;     // disable (0) / Disable after *pedestal* sync events
   int current;      // sync event counter for pedestal feature
   int pulser_arg1;  // fixed pulser argument.  Units of 120ns.
 } TI_SYNCEVENT_CONFIG;
 TI_SYNCEVENT_CONFIG tiSyncEventConfig = {1, 1000, 100, 0, 83};
 using hallc_ti configuation, with new ti_list.c
 HV is off
 pulse, HV off, beam off
 pulse, HV off, beam off
 pulse, HV off, beam off
 HV is on
 pulse, HV on, beam on
 pulse, HV on, beam on
 pulse, HV on, beam on
 ==========================================================================
 go back to use hallc_fadc_ssp configuration, with new ti_list.c
 production, 11:41-12:19, target_type=Loop 2 10cm LH2,shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 FADC config changed to make pedestal arround 100
 slot 7:
 #FADC250_ALLCH_DAC 3205 3170 3170 3195 3195 3190 3200 3195 3180 3205 3190 3215 3170 3215 3175 3205
 FADC250_ALLCH_DAC 3150 3120 3120 3150 3150 3140 3150 3150 3130 3160 3140 3270 3120 3170 3130 3160
 slot 8:
 #FADC250_ALLCH_DAC 3500 3200 3460 3190 3220 3210 3190 3220 3220 3190 3500 3520 3510 3500 3490 3450
 FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3170 3170 3130 3450 3470 3460 3450 3440 3390
 -3111 debug daq, could be good for pedestal
 production, daq crashed, could be good for pedestal
 no data file, coda can not start
 ==========================================================================
 Reboot tunl11 and sbsvme22
 production, 03:02-16:52,target_type=dummy, shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 :21, target changed to Loop 2 10cm LH2, shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 production, 16:53-14:10 July 31st,target=Loop 2 10cm LH2, shms_p=7.913,shms_theta=8.68,hms_p=-2.341,hms_theta=34.15,
 :14  SHMS rotated to 10.86deg, HMS rotated to 13.43deg,
        beam came back at 19:35, target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=10.86,hms_p=-4.256,hms_theta=13.43,
 :01 target changed to dummy,
 :50 SHMS rotated to 8.86 deg,
 :53 target changed back to Loop 2 10cm LH2, shms_p=6.265,shms_theta=8.86,hms_p=-4.256,hms_theta=13.43,
 :12 target changed to dummy,
 :31 target changed back to Loop 2 10cm LH2,
 :12 SHMS rotated to 6.76deg, shms_p=6.265,shms_theta=6.76,hms_p=-4.256,hms_theta=13.43,
 production, 14:10-23:18 July 31st, target_type=Loop 2 10cm LH2,shms_p=6.265,shms_theta=6.76,hms_p=-4.256,hms_theta=13.43,I=40uA
        Target changed to dummp at 14:35, then changed back to Loop 2 at 15:34,
 :58 SHMS angle changed to 7.91 deg, shms_p=6.538,shms_theta=7.91,hms_p=-3.944,hms_theta=17.5,I=40-65uA
 production, 23:18-09:24, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=7.91,hms_p=-3.944,hms_theta=17.5, I=40uA
        Target changed to dummy at 01:40, then to Loop 1 10 cm LD2 at 02:40, beam stopped at 05:00
 production, 09:24-21:59, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=7.91,hms_p=-3.944,hms_theta=17.5, I=40uA
 production, 21:59-11:40, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=7.91,hms_p=-3.944,hms_theta=17.5, I=40uA,
        SHMS rotated to 9.915deg at 5:25 20220802, after that, shms_p=6.538,shms_theta=9.91,hms_p=-3.944,hms_theta=17.5, I=50-65uA
 production,11:42-23:49, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=9.91,hms_p=-3.944,hms_theta=17.5
        Target changed to 10cm dummy at 17:39, then changed to Loop 2 10 cm LH2 at 18:47, this run finished at 23:49
 production, 23:51-08:56, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=9.91,hms_p=-3.944,hms_theta=17.5, I=70uA
        no beam for the fisrt 8 hours
 GEM gas bottle might be emtpy ... need to verify from data
 production, 08:56-11:14, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=9.91,hms_p=-3.944,hms_theta=17.5, I=70uA
        SHMS rotated to 11.91 deg at 10:25, shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5,
 production, 11:14-14:47, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
 production, 14:48-17:39, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
 GEM HV is off
 production, 17:45-20:07, target_type=Loop 2 10cm LH2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
 change target to dummy
 production, 20:22-21:07, target_type=dummy,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
 ====================================================================
 FADC slot 7.11 DAC value changed from 3270 to 3170
 slot 7:
 #FADC250_ALLCH_DAC 3205 3170 3170 3195 3195 3190 3200 3195 3180 3205 3190 3215 3170 3215 3175 3205
 #FADC250_ALLCH_DAC 3150 3120 3120 3150 3150 3140 3150 3150 3130 3160 3140 3270 3120 3170 3130 3160
  FADC250_ALLCH_DAC 3150 3120 3120 3150 3150 3140 3150 3150 3130 3160 3140 3170 3120 3170 3130 3160
 production, 20:22-21:07, target_type=dummy,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
        about 85k events only, but they are good events
 changed target to Loop 1
 production, 21:11-22:41, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
 production, 22:42-02:35, target_type=Loop 1 10cm LD2,shms_p=6.538,shms_theta=11.91,hms_p=-3.944,hms_theta=17.5, I=70uA
 changed target to Loop 2 LH2, then changed target to Loop 2 LH2.
 HMS was rotated 20.57deg,  SHMS was rotated to 8.46deg.
 production, 02:41-08:15, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58,
 production, 08:16-12:41, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58,
 production, 12:41-17:03, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58,
        no beam since 15:30, thunderstorems affect accelerator
 changed target to dummy
 no beam, pedestal run, 17:05-17:05
 no beam, pedestal run, 17:07-17:07
 production, 17:11-21:06, target_type=dummy,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58,
        no beam for the first 100k events
 production, 17:11-23:58, target_type=dummy,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58, I=40uA
        no beam for the first 100k events
 production, 23:58-0:16, target_type=dummy,shms_p=6.719,shms_theta=8.46,hms_p=-3.716,hms_theta=20.58, I=40uA
        SHMS rotated to  10.475deg at 0:08
 production, 0:16-1:09, target_type=dummy,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=40uA
 production, 1:10-02:11, target_type=dummy,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=40uA
 changed target to Loop 2 10cm LH2
 production, 2:13-8:25, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=40uA
 no beam, pedestal run
 :43 HV is off
 :23 HV is ON
 no beam, pedestal run
 no beam, pedestal run
 production, 14:08-21:39, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=40uA
        no beam during the first 100k events. Beam was on for just several minutes.
 production, 21:40-11:20, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=70uA
        no beam during the first 100k events. beam started at 4:05
 production, 11:20-15:44, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=10.475,hms_p=-3.716,hms_theta=20.58, I=70uA
        SHMS angle changed to 12.49 deg at 12:16
 production, 15:44-01:39 August 7th, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=12.49,hms_p=-3.716,hms_theta=20.58
        daq rate 1.5kHz @ I=70uA
 :20 target changed to dummy
 :00 target changed to Loop 2 LH2, I=70uA
 production, 01:39-07:24 August 7th, target_type=Loop 2 10cm LH2,shms_p=6.719,shms_theta=12.49,hms_p=-3.716,hms_theta=20.58
        beam stopped at 7:00
 :30 SHMS rotated 12.28 deg, HMS rotated to 15.06 deg, target was changed to Loop 1 10cm LD2
 ===================================================================
 FADC250_W_WIDTH = 240 for both slot7 and slot8
 pedestal run, no beam
 pedestal run, no beam
 production, 07:34-13:32, target_type=Loop 1 10cm LD2,
        shms_p=-5.127,shms_theta=12.29,hms_p=-5.309,hms_theta=15.04, I=75uA
        From 10:47 to 11:11, target was changed to dummy (I=40uA), at
 :42 target was changed back to Loop 1 10cm LD2, I=75uA
        At 12:42, SHMS was ratated to 14.29deg, at this angle,  daq rate 5.5kHz
        subrun 0-50:  SHMS=12.29deg
        subrun 51:  SHMS=12.29deg and 14.29deg
        subrun 52-60:  SHMS=14.29deg
 production, 13:32-17:50 August 7th, target_type=Loop 1 10cm LD2,
        shms_p=-5.127,shms_theta=14.29,hms_p=-5.309,hms_theta=15.04,
        I=75uA, daq rate 5.5kHz
 :37 target changed to dummy, I=40uA
 :25 target changed to Loop 1 10cm LD2, I=75uA
 :42 SHMS rotated to 16.28deg, I=75uA, daq rate 5.5kHz
        subrun 0-42:  SHMS=14.29deg
        subrun 43:  SHMS=14.29deg and 16.28deg
        subrun 44-45:  SHMS=16.28deg
 production, 17:50-19:26, target_type=Loop 1 10cm LD2, shms_p=-5.127,shms_theta=16.28,hms_p=-5.309,hms_theta=15.04,I=75uA
 production, 19:26-00:01, target_type=Loop 1 10cm LD2, shms_p=-5.127,shms_theta=16.28,hms_p=-5.309,hms_theta=15.04,I=75uA
 :35 changed to dummy target,I=40uA, daq rate 1.6kHz
 production, 00:02-00:33, target_type=dummy, shms_p=-5.127,shms_theta=16.28,hms_p=-5.309,hms_theta=15.04,I=40uA,
        daq rate 1.6kHz, beam stopped at 00:14
 20220808 00:14, rotated SHMS to 16.91 deg, HMS to 19.92 deg
 production, 00:37-01:48, target_type=dummy,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91,I=40uA,
        daq rate 1.6kHz,
        target changed to Loop 1 10cm LD2 at 01:16,
        target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
 production, 00:37-03:11, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
        daq rate 5.6kHz
 production, 03:11-09:11, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
        no beam for the fisrt 100k events, daq rate 5.6kHz
 production, 09:11-10:09, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
        daq rate 5.6kHz
 production, 10:10-13:24, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
        daq rate 5.6kHz
 production, 13:24-15:44, target_type=Loop 1 10cm LD2,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=75uA
        daq rate 5.6kHz
        target changed to dummy at 15:18, I=40uA
 production, 15:44-16:32, target_type=dummy,shms_p=-5.512,shms_theta=16.94,hms_p=-4.752,hms_theta=19.91, I=40uA
        beam stop at 16:03 to prepare for optic
 :09  target changed to single foil Carbon 0.5%, SHMS rotated to 6.8deg and HMS ratated to 12.5deg
 production, 16:32-17:22, target_type=Carbon 0.5%, shms_p=-8.55,shms_theta=6.8,hms_p=-5.587,hms_theta=12.48,I=75uA
        no beam for the first 100k events, daq rate 160Hz
 Target move to Optics 1 +/- 8cm, 2 Foils Carbon
 production, 17:22-17:47, target_type=Optics 1 z=+/-8cm, 2 Foil, shms_p=-8.55,shms_theta=6.8,hms_p=-5.587,hms_theta=12.48,I=50uA
        no beam for the first 100k events, daq rate 80Hz
 production, 17:47-18:02, target_type=Optics 1 z=+/-8cm, 2 Foil, shms_p=-8.55,shms_theta=6.8,hms_p=-5.587,hms_theta=12.48,I=50uA
        only 30k triggers
 :00  target changed to Loop 2 10cm LH2
 production, 18:05-18:57, target_type=Loop2 10cm LH2, shms_p=-8.55,shms_theta=6.8,hms_p=-5.587,hms_theta=12.48,
        I=60uA (18:06), then 20uA(18:08) then 10uA(18:10)
        daq rate 130Hz @20uA, 65Hz @10uA
        SHMS rotated to 7.5deg at 18:28, shms_p=-8.55,shms_theta=7.5,hms_p=-5.587,hms_theta=12.48,I=15uA
 :57  Target changet to Optics 1 +/- 8 cm
 production, 18:59-19:37, target_type=Optics 1 z=+/-8cm, shms_p=-8.55,shms_theta=7.5,hms_p=-5.587,hms_theta=12.48,I=50uA
        daq rate 90Hz @50uA
        target changed to Carbon 0.5% at 19:20, I=75uA
 :38  SHMS rotated to 8.3 deg
 production, 19:39-19:54, target_type=Carbon 0.5%, shms_p=-8.55,shms_theta=8.3,hms_p=-5.587,hms_theta=12.48,I=75uA
 :54  Target changet to Optics 1 +/- 8 cm
 production, 19:54-20:34, target_type=Optics 1 z=+/-8cm, shms_p=-8.55,shms_theta=8.3,hms_p=-5.587,hms_theta=12.48,I=50uA
        no beam for the first 100k events,
        daq rate 90Hz @50uA
 :24 target changed to Loop 2 10cm LH2, beam came back at 20:29
 production, 20:34-21:23, target_type=Loop 2 10cm LH2, shms_p=-8.55,shms_theta=8.3,hms_p=-5.587,hms_theta=12.48,I=20uA
        daq rate 160Hz @20uA, beam stopped at 21:06
 ===================================================
 HV map for FTBF beam test
 HV for FADC channel 0 to 7:
 #   #   SDU#4 SDU#5 THU#2 SDU#2 SDU#1 THU#1
 SC1 SC2 Ecal1 Ecal2 Ecal3 PrSh1 PrSh2 PrSh3
 -1260 -1280 -760 -860 -880 -1640 -1480 -1800 <<== 1~8GeV
 This setting was also used for some 1GeV calibrations
 -1260 -1300 -880 -920 -940 -1640 -1440 -1800 <<== <1GeV
 ---------------------------------------
 GeV calibration start
 Moved table to (1505, 337), center on the left block 51,563 events
 Moved table to (1389, 337), center on the right block 77621 events
 Moved table to (1447, 243), center on the top block 52034 events
 GeV calibration end
 ---------------------------------------
 ---------------------------------------
 GeV calibration start, MWPC 1 is not working
 move to Top block, use this New HV: 1260, 1300, 880, 920, 940, 1640, 1440, 1800, FADC ch11 and ch12 swapped.
 These two channels are down stream Cherenkov. After swapped, Down cherenkov inner PMT is in ch12.
 move to left block, point B (1498,347)
 beam on the center of the left block, point B
 beam on the center of the right block, point C (1382,347)
 beam on the center of the top block, point A (1440, 252)
 GeV calibration end
 ---------------------------------------
 =====================================================
 -----------------------------------------------
 change HV to the same as FermiLab
 #     #    SDU#4 SDU#5 THU#2 SDU#2 SDU#1 THU#1
 SC1   SC2  Ecal1 Ecal2 Ecal3 PrSh1 PrSh2 PrSh3
 -1260 -1280 -760  -860  -880 -1640 -1480 -1800 <<== 1~8GeV
 ===>
 slot10.7(SDU#1) slot10.8(THU#1) slot10.9(SDU#2)
 -1480           -1800           -1640
 slot2.0(SDU#4)  slot2.1(THU#2)  slot2.2(SDU#5)
 -760            -880            -860
 -----------------------------------------------
 :40 SHMS rotated to 12.25deg, HMS rotated to 15.7deg
 -----------------------------------------------
 :11 target changed to dummy
 production, 22:10-22:21,target_type=dummy,shms_p=-8.035,shms_theta=12.25,hms_p=-6.792,hms_theta=15.69,I=40uA
 	no beam at the first 100k triggers
 :34   SHMS rotated to 13.15deg, HMS rotated to 17.72deg
 production, 22:22-23:22,target_type=dummy,shms_p=-8.035,shms_theta=13.15,hms_p=-6.792,hms_theta=17.72,
 	no beam at the first 100k triggers, beam came at 22:32.  only 9 minutes of dummy data
 :41 stopped beam to changed target to Loop 2 10cm LH2
 :46 beam came back and then went away at 22:53 due to HMS Q1 interlock,
 :12 beam came back again, shms_p=-8.035,shms_theta=13.15,hms_p=-6.792,hms_theta=17.72, I=60uA,
 	daq rate 1.1kHz, 10 minutes of LH2 data
 production, 23:22-23:52 August 8th,
        target=Loop 2 10cm LH2, shms_p=-8.035,shms_theta=13.15,hms_p=-6.792,hms_theta=17.72, I=60uA
        daq rate 1.1kHz
        beam stopped at 23:38 then SHMS rotated to 14.02 deg and HMS rotated to 19.86deg
        beam came back at 23:49, I=75uA, shms_p=-8.035,shms_theta=14.02,hms_p=-6.792,hms_theta=19.86,
        subrun 0:  SHMS=13.15deg
        subrun 1:  SHMS=13.15deg and 14.02deg
 production, 23:52-02:03 August 9th,
        target=Loop 2 10cm LH2, shms_p=-8.035,shms_theta=14.02,hms_p=-6.792,hms_theta=19.86, I=75uA
        daq rate 1.9kHz
 :51 target changed to dummy, I=40uA,
 :16 SHMS rotated to 14.895deg,	shms_p=-8.035,shms_theta=14.9,hms_p=-6.792,hms_theta=19.86, I=75uA
 :45 target changed to Loop 2 LH2, beam came back at 01:49 but stopped at 01:58
        subrun 0-3 are for 14.02 deg SHMS
        subrun 4 are for both 14.02 and 14.9 deg SHMS
        subrun 5-6 are for 14.9 deg SHMS
 production, 02:03-08:35,target=Loop 2 10cm LH2, shms_p=-8.035,shms_theta=14.9,hms_p=-6.792,hms_theta=19.86,I=75uA
        no beam at the first 100k triggers,beam came back at 03:18,
 :45, SHMS rotated to 15.785deg, shms_p=-8.035,shms_theta=15.79,hms_p=-6.792,hms_theta=19.86,I=70uA
 :05, target changed to dummy, I=40uA, took 8 minutes of data
 :25, SHMS rotated to 13.58deg, took 8 minutes of data for dummy, I=40uA,
 :47, changed target to Loop2 LH2, shms_p=-7.913,shms_theta=13.58,hms_p=-6.792,hms_theta=19.86,
 :00, SHMS rotated to 12.69deg, took 4 minutes of data till beam stopped at 08:04 to change pass,
        shms_p=-8.035,shms_theta=12.69,hms_p=-6.792,hms_theta=16.03,I=70uA
 ==============================================================================================================
 Aug 9th 08:05 Accelerator changed beam from 5-pass to 4-pass for Hall C. Beam energy is 8.494GeV
 pedestal, 100k pulse triggers, no beam
 pedestal, 100k pulse triggers, no beam
 :48 HMS rotated to 20.905deg, SHMS rotated to 6.93deg
 production, 09:02-15:08, target=Loop 2 LH2, shms_p=6.265,shms_theta=6.93,hms_p=-2.193,hms_theta=20.89,
        no beam at the first 100k triggers,beam came back at 14:02,
 :00 target changed to Carbon Hole, I=5uA for 6 minutes,
 :18 target changed to Loop 2 LH2, I=35uA, beam came back at 14:20, daq rate 220Hz, beam stopped at 14:46
 production, 15:09-21:31, target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=6.93,hms_p=-2.193,hms_theta=20.89,
        no beam at the first 100k triggers,beam came back at 17:31, I=60uA
 :37  target changed to dummy
 production, 21:31-22:28, target=dummy, shms_p=6.265,shms_theta=6.93,hms_p=-2.193,hms_theta=20.89
        no beam for the first 100k triggers,
 :35 beam arrived, beam current linear ran up from 3uA to 23uA at 21:55 to do Ion Chamber calibration
        From 21:56, I=40UA till 22:15
 :15  SHMS rotated to 8.93 deg, beam came back at 22:20
        target=dummy, shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89
 production, 22:28-22:44, target=dummy, shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89
 :46  target changed to Loop 2 LH2
 production, 22:48-00:05 August 10th,
        target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89, I=80uA
        no beam for the first 100k triggers,daq rate 770Hz
 production, 00:05-01:22,
        target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89, I=80uA
        daq rate 770Hz, beam stopped at 00:49 due to Vacuum issue at VBV3H08A
 pedestal, pulse run, 01:23-10:26, no beam for the whole run,1000006 events
 pedestal, pulse run, 11:29-11:29, no beam
 =========================================================================================
 Add "PreSh_t && Shower_t" into TS#2, 20220810
 pedestal, pulse run, 14:54-15:19, no beam
 pedestal, pulse run, 15:47-15:47, no beam
 :00   SHMS rotated to 5.5 deg.
 production, 17:21-23:07, target=Loop 2 10cm LH2, shms_p=6.265,shms_theta=5.53,hms_p=-2.193,hms_theta=20.89,
        no beam for the sirst 100k triggers, tune beam arrived at 17:52, real beam arrived at 21:34
 :09 Changed FADC slot8.9 DAC value from 3130 to 3440.  After feed it into FIFO, its pedestal changed
 production,23:10-02:38 August 11th,
       target=Loop 2 LH2, shms_p=6.265,shms_theta=5.53,hms_p=-2.193,hms_theta=20.89,I=30uA
       daq rate 320Hz
 production,02:38-04:38, target=Loop 2 LH2, shms_p=6.265,shms_theta=5.53,hms_p=-2.193,hms_theta=20.89,I=30uA
       daq rate 320Hz
 :05 target changed to dummy, I=40uA
 :45 HMS rotated to 28.41deg,
       target=dummy,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41, I=40uA, daq rate 320Hz
 production, 04:39-09:03, target=dummy,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
       I=40uA, daq rate 320Hz
 :50 target chagned to Loop 2 LH2, I=35uA
       target=Loop 2 LH2, shms_p=6.265,shms_theta=5.53,hms_p=-2.193,hms_theta=28.41,I=35uA
       Acceleration maintenence started from 6:30
 production, 19:55-01:52 August 12th, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
       no beam for the first 100k triggers, tune beam came back at 23:32
 production, 01:52-09:28, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
       daq rate = 400Hz @ I=38uA. Beam stopped at 09:10
 :21 A beam energy measurement is scheduled at 9:30-ish AM. Target parked at 'home'.
 :29 Target changed to Loop 2 LH2
 production, 11:35-12:26, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
       no beam for the first 100k triggers, beam came back at 11:50 and went away at 12:01
 production, 14:05-14:41, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
       daq rate = 400Hz @ I=38uA.
 production, 14:42-16:46, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
        no beam for the first 100k triggers, beam came back at 14:49
        beam stopped at 16:12
 production, 16:49-00:54 August 13th, target=Loop 2 LH2,
       shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
        no beam for the first 100k triggers, beam came back at 17:48
 production, 00:54-02:28, target=Loop 2 LH2,shms_p=6.538,shms_theta=5.53,hms_p=-1.882,hms_theta=28.41,
       daq rate = 450Hz @ I=40uA.
 :09 SHMS rotated to 7.47 deg, trying to ramp beam current up to 80uA
       subrun 0: 5.53deg and 7.47deg
       subrun 1-3: 7.47deg
 production, 02:28-12:05, target=Loop 2 LH2,shms_p=6.538,shms_theta=7.47,hms_p=-1.882,hms_theta=28.41,
       daq rate = 1024Hz @ I=79uA.
 production, 12:05-14:42, target=Loop 2 LH2,shms_p=6.538,shms_theta=7.47,hms_p=-1.882,hms_theta=28.41,
       daq rate = 1024Hz @ I=79uA.
 :28 target changed to dummy, I=40uA, daq rate 320Hz
 production, 14:42-16:01, target=dummy,shms_p=6.538,shms_theta=7.47,hms_p=-1.882,hms_theta=28.41,
       I=40uA, daq rate 320Hz
 :01 SHMS rotated to 9.5deg, target changed to Loop 2 LH2
 production, 14:01-17:29, target=Loop 2 LH2,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
       no beam for the first 100k triggers, beam came back 16:04
       daq rate = 1024Hz @ I=79uA.
       beam stopped at 17:13, 4th pass separation issue
 production, 17:37-00:35 August 14th, target=Loop 2 LH2,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
       no beam for the first 100k triggers, beam came back 17:41
       daq rate 1.5kHz @ I=80uA
 production, 00:35-03:53 August 14th, target=Loop 2 LH2,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
       daq rate 1.5kHz @ I=80uA
 :31 target changed to dummy, I=40uA
 production, 03:53-04:13, target=dummy,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
       I=40uA, daq rate 512Hz
 production, 04:13-04:31, target=dummy,shms_p=6.538,shms_theta=9.5,hms_p=-1.882,hms_theta=28.41,
       I=40uA, daq rate 512Hz
 :38 target changed to Loop 2 LH2
 :50 SHMS rotated to 8.93 deg, HMS rotated to 20.89deg
 production, 05:01-13:02, target=Loop 2 LH2,shms_p=6.265,shms_theta=8.93,hms_p=-2.193,hms_theta=20.89,
       no beam for the first 100k triggers, beam came back 7:35, I=80uA
       beam stopped at 10:32, then came back at 12:15
       ~11:00  SHMS rotated to 30.02deg, HMS rotated to 19.56deg
       target=Loop 2 LH2,shms_p=3.731,shms_theta=30.02,hms_p=-5.587,hms_theta=19.56
       ---> SHMS=8.93deg for subrun 0-3, SHMS=30.02deg for subrun 5 to 10, subrun 4 contains both angles <---
 production, 13:02-13:14, target=Loop 2 LH2,shms_p=3.731,shms_theta=30.02,hms_p=-5.587,hms_theta=19.56,I=80uA
       At 13:07, target changed to dummy, I=40uA.  Only 2 minutes of LH2 target then 2 minutes of dummy target
 production, 13:14-13:25, target=dummy,shms_p=3.731,shms_theta=30.02,hms_p=-5.587,hms_theta=19.56,
       daq rate 1.5kHz @ I=40uA
 production, 13:25-13:30, target=dummy,shms_p=3.731,shms_theta=30.02,hms_p=-5.587,hms_theta=19.56,
       daq rate 1.5kHz @ I=40uA, only 2 minutes of data then beam stopped for target change
 :32 target changed to Loop 2 LH2,
 :32 SHMS rotated to 28.355deg. HMS rotated to 20.905deg
 production, 13:33-13:44, target=Loop 2 LH2, shms_p=3.996,shms_theta=28.40,hms_p=-5.321,hms_theta=20.91,
       daq rate 1.8kHz @ I=80uA, beam stopped at 13:41
 production, 13:45-14:39, target=Loop 2 LH2, shms_p=3.996,shms_theta=28.40,hms_p=-5.321,hms_theta=20.91,
       daq rate 1.8kHz @ I=80uA,
       I stopped coda at 13:44 for previous run because HallC coda was stopped at 13:41 in order to adjust
       SHMS angle from 28.44 to 28.355.
       I was taking data during this adjustment. This change should not affect the ecal setup.
 :40 target changed to dummy
 production, 14:41-14:58. target=dummy, shms_p=3.996,shms_theta=28.355,hms_p=-5.321,hms_theta=20.91,
       I=40uA, daq rate 620Hz
 :00 target changed to Loop 2 LH2,
 :30 Set HMS angle to 15.065 and SHMS angle to 9.455 deg, but stayed at 15.05 deg and 9.53deg
 production, 15:01-17:03, target=Loop 2 LH2, shms_p=-7.559,shms_theta=9.53,hms_p=-6.477,hms_theta=15.05,
       no beam for the first 100k triggers, beam came back 15:37, I=20uA
 :51 target changed to dummy,shms_p=-7.559,shms_theta=9.53,hms_p=-6.477,hms_theta=15.05,
 :38 SHMS rotated to 11.97 deg,HMS rotated to 15.62 deg
       target=dummy, shms_p=-7.106,shms_theta=11.97,hms_p=-5.878,hms_theta=15.62,
 :02 target changed to Loop 2 LH2, shms_p=-7.106,shms_theta=11.97,hms_p=-5.878,hms_theta=15.62,
       subrun 0: SHMS=9.455deg and 11.97deg
       subrun 1: SHMS=11.97deg
 production, 17:05-17:50, target=Loop 2 LH2, shms_p=-7.106,shms_theta=11.97,hms_p=-5.878,hms_theta=15.62,
       no beam for the first 100k triggers, beam came back at 15:11, I=10uA,
       beam went away at 17:24 due to injector problem, only 3~4 minutes of beam in this run, 175k events
 production, 17:57-19:49, target=Loop 2 LH2, shms_p=-7.106,shms_theta=11.97,hms_p=-5.878,hms_theta=15.62,
       no beam for the first 100k triggers, beam came back at 18:17, I=10uA till 18:45
 :47 SHMS rotated to 13.92, HMS rotated to 17.96deg, beam came at 19:13, I=55uA
       target=Loop 2 LH2, shms_p=-6.72,shms_theta=13.92,hms_p=-5.878,hms_theta=17.96,
       subrun 0: SHMS=11.97deg and 13.92deg
       subrun 1-4: SHMS=13.92deg
 production, 19:49-19:54, target=Loop 2 LH2, shms_p=-6.72,shms_theta=13.92,hms_p=-5.878,hms_theta=17.96,
       beam stopped at 19:51, only 256k events
 :56 target changed to dummy
 production, 19:57-20:11, target=dummy, shms_p=-6.72,shms_theta=13.92,hms_p=-5.878,hms_theta=17.96,
 :12 SHMS rotated to 14.82 deg, HMS rotated to 20.37deg
 production, 20:13-20:36, target=dummy, shms_p=-6.538,shms_theta=14.82,hms_p=-5.878,hms_theta=20.37,
       no beam for the first 100k triggers, beam came back at 20:20, I=40uA, daq rate 1920Hz
 :35 target changed to Loop 2 LH2
 production, 20:40:21:16, target=Loop 2 LH2, shms_p=-6.538,shms_theta=14.82,hms_p=-5.878,hms_theta=20.37,
       no beam for the first 100k triggers, beam came back at 20:42, I=80uA,
       beam stopped at 21:12 to prepare optics runs
 :18 HMS rotated to 13 deg, target changed to Carbon 0.5%
 production, 21:16-22:05, target=Carbon 0.5%,
       Sieve Optics,shms_p=-6.538,shms_theta=14.82,hms_p=-5.878,hms_theta=12.98,
       no beam for the first 100k triggers, beam came back at 21:30,
       I=4.5uA --> daq rate 64Hz,
       I=13uA --> daq rate 192Hz,
       I=80uA --> daq rate 1216Hz,
 :02 target changed to optics 1, Carbon +/- 8cm, I=3uA
 production, 22:05-23:21, target=Opitcs 1, Carbon 2-foils +/- 8cm,
       Sieve Optics,shms_p=-6.538,shms_theta=14.82,hms_p=-5.878,hms_theta=12.98,
       ramp currunet from 2uA till 40 uA
       I= 10uA --> daq rate 128Hz
       I= 15uA --> daq rate 192Hz
       I= 20uA --> daq rate 256Hz
       I= 49.5uA --> daq rate 576Hz
 :24  target changed to Loop LH2
 :30  SHMS rotated to 16.100deg, HMS rotated to 17.235deg
 production, 23:27-00:06, target=Loop 2 LH2, shms_p=-6,shms_theta=16.17,hms_p=-5.587,hms_theta=17.23,
       no beam for the first 100k triggers, beam came back 23:47,
       daq rate is 1.2kHz @ I=25uA
 production, 00:06-00:30, target=Loop 2 LH2, shms_p=-6,shms_theta=16.17,hms_p=-5.587,hms_theta=17.23,
       daq rate is 1.280Hz @ I=25uA
 :30 target changed to dummy
 production, 00:32-01:24, target=dummy, shms_p=-6,shms_theta=16.17,hms_p=-5.587,hms_theta=17.23,
       no beam for the first 100k triggers, beam came back 00:35,not staple until 00:42
       daq rate 1.8 kHz @ I=40uA
 production, 01:24-01:36, target=dummy, shms_p=-6,shms_theta=16.17,hms_p=-5.587,hms_theta=17.23,
 :38 SHMS rotated to 19.20deg,  HMS rotated to 19.505deg
 production, 01:39-03:02, target=dummy, shms_p=-5.646,shms_theta=19.28,hms_p=-5.587,hms_theta=19.5,
       no beam for the first 100k triggers, beam came back 02:42,
 :05 changed target to Loop 2 LH2
 production, 03:04-03:48, target=Loop 2 LH2,shms_p=-5.646,shms_theta=19.28,hms_p=-5.587,hms_theta=19.5,
       daq rate 3.7 kHz @ I=73uA
       daq rate 3.9 kHz @ I=77uA
 :51 SHMS Rotated to 23.3 degrees, HMS Rotated to 21.875 degrees
 production, 03:53-5:44, target=Loop 2 LH2, shms_p=-4.902,shms_theta=23.2,hms_p=-5.587,hms_theta=21.875,
       no beam for the first 100k triggers, beam came back at 04:37,
       daq rate 3.9 kHz @ I=77uA
 :45 changed target to dummy
 production, 05:48-06:04, target=dummy, shms_p=-4.902,shms_theta=23.2,hms_p=-5.587,hms_theta=21.875,
       no beam for the first 100k triggers, beam came back at 05:53, stopped at 5:58
       daq rate 1.8 kHz @ I=40uA
 production, 6:06-06:18, target=dummy, shms_p=-4.902,shms_theta=23.2,hms_p=-5.587,hms_theta=21.875,
       daq rate 1.8 kHz @ I=40uA
 :18  Rotated SHMS to 25.1 deg, rotated HMS to 40 deg, change momenta for both of them,
 pedestal run, internal pulse, no beam since 06:18
       Something went wrong, Hall C configuration change could not finish within 45 minutes and further more
       the injector has some problem. HallC has been scheduled a controlled access up to six hours from 8AM
       for the aerogel exchange.
 :46 target changed to Loop 2 LH2
 :40 SHMS rotated to 18.9deg, HMS rotaed to 12.11deg
 production, 13:36-14:03, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
       daq rate 4.0 kHz @ I=79uA
 production, 14:03-15:10, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
       daq rate 3.9 kHz @ I=77uA
 production, 15:11-15:53, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
 production, 15:53-16:15, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
 production, 16:16-17:58, target=Loop 2 LH2, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
       no beam for the first 100k triggers, beam came back at 16:40,
       daq rate 4.0 kHz @ I=79uA
 :00 changed target to dummy
 production, 18:02-18:16, target=dummy, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
       no beam for the first 100k triggers, beam came back at 18:04,
       daq rate 1.9 kHz @ I=40uA
 production, 18:17-19:09, target=dummy, shms_p=2.792,shms_theta=18.9,hms_p=-5.587,hms_theta=12.11,
       daq rate 1.9 kHz @ I=40uA
 :10 target changed to Loop 2 10 cm LH2
 :12 SHMS rotated to 21.22deg
 production, 19:14-20:38, target=Loop 2 LH2, shms_p=2.792,shms_theta=21.22,hms_p=-5.587,hms_theta=12.11,
       daq rate 4.0 kHz @ I=79uA
 production, 20:39-21:41, target=Loop 2 LH2, shms_p=2.792,shms_theta=21.22,hms_p=-5.587,hms_theta=12.11,
       daq rate 4.0 kHz @ I=79uA
 :35 target changed to dummy, beam came back at 21:40,
       the last one minutes is dummy events, I=40uA, daq rate 1.8kHz
 production, 21:41-22:14, target=dummy, shms_p=2.792,shms_theta=21.22,hms_p=-5.587,hms_theta=12.11,
        I=40uA, daq rate 1.8kHz
 :15 target changed to Loop 2 LH2, SHMS rotated to 23.215deg, actually it is 22.9deg
 production, 22:17-23:28, target=LH2, shms_p=2.792,shms_theta=22.9,hms_p=-5.587,hms_theta=12.11,
       I=76uA, daq rate 3.9kHz
 production, 23:28-00:05, target=LH2, shms_p=2.792,shms_theta=22.9,hms_p=-5.587,hms_theta=12.11, I=80uA
 :35 beam stopped, changed to dummy target, beam came back at 23:44, I=40uA
       subrun 0 -->  LH2
       subrun 1 -->  part LH2 and part dummy
       subrun 2 -->  dummy
 :11 SHMS rotated to 21.22 deg on camera(true angle is 20.9 after subtracting offset), target changed to LH2
       The SHMS angle in HallC log is 22.17, that is a typo
 production, 00:05-00:51, target=LH2, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
       no beam for the first 100k triggers, beam came back at 00:16,
       beam went away at 00:25 due to accelerator issue, 129k events
 production, 00:59-04:21, target=LH2, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
      no beam for the first 100k triggers, beam came back at 03:15,
 kHz @ I=20uA
 .2kHz @ I=65uA
 production, 04:21-05:02, target=LH2, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
 .4kHz @ I=29uA
 :03 changed to dummy target
 production, 05:07-05:36, target=dummy, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
 .4kHz @ I=30uA
 production, 05:37-10:28, target=dummy, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11
      no beam for the first 100k triggers, beam came back at 5:55 last till 6:03.
      Since 6:03, HMS Q1 was tripped, Hall C could not take beam.
 :37 target changed to LH2
 :03, beam was back again, I=12uA, target=LH2, shms_p=2.792,shms_theta=20.9,hms_p=-5.587,hms_theta=12.11,
 :10, beam stopped for pass changed
      subrun 0 has both dummy and LH2 target
      subrun 1 and 2 are for LH2 target only
 =======================================================================================================
 :15 August 16th, started to change to 3-pass beam , E = 6.399 GeV
 :30 SHMS rotated to 17.91 deg, camera shows 18.23 due to the encoder offset 0.32.
 :00 Reset SHMS angle offset to zero so the camera shows the same value as the encoder.
       Set the SHMS to 17.86 degrees and the HMS to 18.31.
 pedestal, pulse run, cosmic 12:42 August 16th - 12:05 August 17th, 100203 events
 pedestal, pulse run, cosmic, 12:41-14:38,  1000021 events
 memeory upgraded to 24G in daq machine tunl11.jlab.org
 tune beam came back to Hall C
 :17 target changed to carbon hole
 16:58-17:04 pedestal, pulse run,
 -3255  debug daq, trash
 :48 target changed to Loop2 LH2
 17:52-18:01 pedestal, pulse run, debug daq, good for pedestal only
 production, 18:08-18:16, target=LH2,shms_p=2.412,shms_theta=17.86,hms_p=-3.921,hms_theta=13.81,
 production, 18:22-19:35, target=LH2,shms_p=2.412,shms_theta=17.86,hms_p=-3.921,hms_theta=13.81,
       daq rate 1152Hz @ I=25uA
       daq rate 2.3kHz @ I=50uA
 :36 target changed to dummy
 production, 19:36-20:02, target=dummy,shms_p=2.412,shms_theta=17.86,hms_p=-3.921,hms_theta=13.81,
       no beam for the first 100k triggers, beam came back at 19:40,
       daq rate 1664Hz @ I=40uA
 :02 SHMS rotated to 19.86 deg
 production, 20:03-20:24, target=dummy, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
       no beam for the first 100k triggers, beam came back at 20:07,
       daq rate 1664Hz @ I=40uA
 :24 target changed to LH2
 production, 20:26-20:35, target=LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
       no beam for the first 100k triggers, beam came back at 20:28,
 production, 20:42-21:01, target=Loop 2 LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
       daq rate 2.7kHz @ I=60uA
 production, 21:03-21:39, target=Loop 2 LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
       no beam for the first 100k triggers, beam came back at 21:16,
       daq rate 2.7kHz @ I=60uA
 production, 21:39-21:52, target=Loop 2 LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
       daq rate 2.7kHz @ I=60uA
 production, 21:54-22:23, target=Loop 2 LH2, shms_p=2.412,shms_theta=19.86,hms_p=-3.921,hms_theta=13.81,
       daq rate 2.8kHz @ I=60uA
 -------- 22:25 SHMS spectrometer change to 21.85-------------
 production, 22:28-22:47, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81,
       daq rate 3.2kHz @ I=70uA. Note, it seems they were pushing to reach 80 uA, so the current and rate is may         fluctuate
 production, 22:47-23:14, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
       daq rate 3.6kHz @ I=80uA
       no beam for the first 100k triggers, beam came back at 22:49
 production, 23:15-23:43, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
       daq rate 3.6kHz @ I=80uA
 production, 23:43-23:55, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
       daq rate 3.6kHz @ I=80uA
 production, 23:56-24:04, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
       daq rate 3.60kHz @ I=0uA
       no beam for the first 100k triggers, beam was off for 10 minutes due to accelerator issues
 production, 00:07-00:15, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
       daq rate 3.6kHz @ I=80uA
 ---------- 00:20 Switch target to Dummy ---------
 production, 00:19-00:45, target=10 cm Dummy, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.81
       no beam for the first 100k triggers, beam returned at 00:24
       daq rate 1.6kHz @ I=40uA
 ---------00:50 Switch target to LH2-------
 production, 00:56-02:22, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.85,hms_p=-3.921,hms_theta=13.8
       daq rate 1.8kHz @ I=40uA
 production, 02:23-3:04, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.86,hms_p=-3.921,hms_theta=13.8
       daq rate 850Hz @ I=20uA
       daq rate 512Hz @ I=12uA
 production, 03:04-04:44, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.86,hms_p=-3.921,hms_theta=13.8
       daq rate 512Hz @ I=12uA
 production, 04:44-8:49, target=Loop 2 LH2, shms_p=2.412,shms_theta=21.86,hms_p=-3.921,hms_theta=13.8
       daq rate 512Hz @ I=12uA
       HallC was doing FADC dead time study. current changed from 12uA, to 60uA then to 30uA
 :27 HMS rotated to 18.595deg, SHMS roated to 37.97deg
 :00 I=75UA, target=LH2, shms_p=2.412,shms_theta=38,hms_p=-4.752,hms_theta=18.61,
 :28 target changed to dummy, I=40uA
 :48 HMS rotated to 21.095deg, SHMS rotated to 34.465deg
       	    target=dummy, shms_p=2.792,shms_theta=34.49,hms_p=-4.391,hms_theta=21.11,
 :15 target changed to LH2, I=75uA
       	    target=LH2, shms_p=2.792,shms_theta=34.49,hms_p=-4.391,hms_theta=21.11,
 	    subrun   0-6: SHMS=21.86deg
 	    subrun     7: SHMS=21.86deg and 37.97deg
  	    subrun  8-11: SHMS=37.97deg
 	    subrun    12: SHMS=37.97deg and 34.49deg
 	    subrun 13-16: SHMS=34.49deg
 :59  HMS rotated to 26.55deg, SHMS rotated to 28.46deg
 production, 08:53-10:45, target=LH2, shms_p=3.493,shms_theta=28.47,hms_p=-3.727,hms_theta=26.56,
       no beam for the first 100k triggers, beam returned at 09:30, I=75uA
 :10 target changed to dummy, I=40uA
 :27 beam stopped
 ===================20020818 Install VTP board=========================
 From here EPICS variables are inserted into ER
 SHMS at 7.66deg and HMS at 28.78deg.
 -3283 debug daq runs. HV are off. no beam.  good for pedestal
 HV are turned on in the middle of run 3283, but no beam after HV is on.
 production, 20:20-23:14, target=LH2,shms_p=4.605,shms_theta=7.66,hms_p=-1.727,hms_theta=28.78,
       no beam for the first 100k triggers, beam came back at 21:11
       daq rate 750Hz @ I=75UA
 :00 target changed to dummy
 :40 SHMS rotated to 9.66deg, target changed to LH2
       target=LH2,shms_p=4.605,shms_theta=9.66,hms_p=-1.727,hms_theta=28.78,
       daq rate 1235Hz @ I=75UA
       subrun 0 contains data for SHMS=7.66deg
       subrun 1 contains data for both 7.66deg and 9.66
       subrun 2-3 contains data for SHMS=9.66deg
 production, 23:19-00:52 August 19th, target=LH2,shms_p=4.605,shms_theta=9.66,hms_p=-1.727,hms_theta=28.78,
       daq rate 1235Hz @ I=75UA
 production, 00:54-05:28, target=LH2,shms_p=4.605,shms_theta=9.66,hms_p=-1.727,hms_theta=28.78,
       coda lost roc3 at 01:15 and did not take data since then.
 :00  changed target to dummy
 :23 SHMS rotated to 11.66deg,
 :50 target changed to LH2,shms_p=4.605,shms_theta=11.67,hms_p=-1.727,hms_theta=28.78,
 production, 05:29-12:57,target=LH2, shms_p=4.605,shms_theta=11.67,hms_p=-1.727,hms_theta=28.78,
 :25 SHMS rotated to 10deg and HMS to 42.23deg
       target=LH2,shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       no beam between 10:09 and 11:20
       daq rate 1.5kHz @ I=77uA
       subrun 0-19: 11.67deg
       subrun 20: 11.67deg and 10deg
       subrun 21-29: 10deg
 production, 12:57-18:12, target=LH2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       daq rate 1.5kHz @ I=77uA
 production, 18:14-18:31, target=LH2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       daq rate 1.5kHz @ I=77uA
 production, 18:31-00:06 August 20th, target=LH2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       daq rate 1.5kHz @ I=77uA
 :09 target changed to dummy, I=40uA
       daq rate 512Hz @ I=40uA
 production, 00:08-00:34 August 20th, target=dummy, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       daq rate 512Hz @ I=40uA
 :26 target changed to LD2
       Ion chamber calibration start from 00:31
 production, 00:34-00:49 August 20th, target=LD2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       beam current ramped up from 0 to 32uA for Ion chamber calibration
 production, 00:50-08:50 August 20th, target=LD2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       daq rate 3.2kHz @ I=77uA
 production, 08:51-14:18 August 20th, target=LD2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       daq rate 3.2kHz @ I=77uA
 :36  SHMS rotated to 8deg,
       target=LD2, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26, daq rate 2.0kHz @ I=78.5uA
       subrun 0-12: SHMS=10 deg
       subrun 13: SHMS=10 deg and 8 deg
       subrun 14-30: SHMS=8deg
 production, 14:18-01:19 August 21st, target=LD2, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
       daq rate 2.0kHz @ I=78.5uA
 :18 taret changed to dummy, I=40uA
       subrun 0-48: LD2
       subrun 49: LD2 and dummy
       subrun 50: dummy
 production, 14:18-01:21 August 21st, target=dummy, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
       just 106k events
 production, 01:24-02:54 August 21st, target=dummy, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
       daq rate 500Hz @ I=40uA
 :36  changed to LH2 target, I=80uA
 production, 02:55-14:46 August 21st, target=LH2, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
       daq rate 1000Hz @ I=78uA
 production, 14:46-19:00 August 21st, target=LH2, shms_p=5.127,shms_theta=8,hms_p=-1.158,hms_theta=42.26,
       daq rate 1000Hz @ I=78uA
 :01 SHMS rotated to 10deg
 production, 19:02-00:57 August 22th, target=LH2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       daq rate 1500Hz @ I=78uA
 :47 target changed to LD2
 production, 00:57-02:51 August 22nd, target=LD2, shms_p=5.127,shms_theta=10,hms_p=-1.158,hms_theta=42.26,
       daq rate 3.5 kHz @ I=80uA
       beam stopped at 02:41
 :55 target changed to LH2
 :00 SHMS rotated to 7.5deg, HMS rotated to 29.55deg
 :00 HMS Q1 interlock happened and SHMS Dipole did not response. Hall is in controlled access.
 :00 Accelerator fire alarm, no beam.
 pedestal, 02:51-09:09 August 22nd, no beam
 :50 SHMS rotated to 5.5deg,
 production, 15:01-01:04 August 23rd, target=LH2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
       no beam until 16:20
       daq rate 500Hz @ I=40uA
 production, 01:04-04:02 August 23rd, target=LH2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
       daq rate 500Hz @ I=40uA
 :00 changed to dummy target
       beam stop at 03:15,  Trim rack W301B13 negative bulk supply fail
 production, 04:04-11:33 August 23rd, target=dummy, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
       no beam at the beginning until 04:58
 :25 target changed to LD2
 :23 target changed to 'home' (absolute empty) for BCM calibration
 ==================================================================================
 run 3171-3305 were using the same HV as FermiLab, but the HV for Shower_L is too low,
 the amplitude of the signal is about 10mv.
 Here is the new HVs:
 Slot  2
 Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
 HV:              1080             1100              930   1050   1050   1050   1050
 Slot 10
 Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B,  SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
 HV:    1600   1600   1700   1750      850     1000  1950                1550                1800               1750
 :54 target changed to Loop 1 10cm LD2
 procudtion, 12:55-14:20 August 23rd, target=LD2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
       no beam for the first 100k triggers, beam came back at 13:18
       daq rate = 2.7kHz @ I=31uA
       daq rate = 3.0kHz @ I=33uA
       This daq rate is too high comparing to run 3307. The beam might scratch the target frame.
 ==========HV changed=======
 Lower HVs for preshower_top and all 3 Ecal blocks
 Slot 2
 Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
 HV: 1030 1050 900 1050 1050 1050 1050
 Slot 10
 Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B, SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
 HV: 1600 1600 1700 1750 850 1000 1950 1550 1800 1700
 procudtion, 14:23-18:23 August 23rd, target=LD2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
       daq rate = 1.7kHz @ I=31uA
 ==========HV changed=======
 :24 Adjusted TOP preshower (-40V) and top shower HVs (-30V)
 Slot  2
 Name: Shower_L(SDU#4), Shower_R(THU#2), Shower_T(SDU#5), CherA, CherB, CherC, CherD
 HV:              1030             1050              870   1050   1050   1050   1050
 Slot 10
 Name: SC0_T, SC0_B, SC1_T, SC1_B, LASPD_T, LASPD_B,  SPD, Preshower_L(SDU#1), Preshower_R(THU#1), Preshower_T(SDU#2)
 HV:    1600   1600   1700   1750      850     1000  1950                1550                1800               1660
 procudtion, 18:25-18:34 August 23rd, target=LD2, shms_p=5.422,shms_theta=5.49,hms_p=-0.96,hms_theta=29.57,
       daq rate = 1.0kHz @ I=31uA
 ==========HV changed=======
 SC1_top 1700 -> 1680
 Top preshower 1660-> 1640
 Top SHower 870 -> 850
 :45 SHMS rotated to 7.5 deg
 procudtion, 18:48-20:08 August 23rd, target=LD2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
       no beam for the first 100k triggers, beam came back at 19:36
       beam stopped at 19:54 due to accelerator issue.
 production, 20:11-03:17 August 24th, target=LD2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
       daq rate 1.7kHz @I=80uA
 procudtion, 03:17-12:33 August 24th, target=LD2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
       no beam for the first 100k triggers, beam came back at 03:18
       daq rate 1.7kHz @I=80uA
 :38  changed target to dummy, I=40uA
 :40 changed target to 'home'(absolute empty) for beam energy measurement, I=100nA, daq rate=1.2kHz
 trash, 12:38-12:44 August 24th, target=empty(?), shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
       daq rate=1.2kHz @ I=0.1uA,  the beam must have scratched something, 173k events
       beam energy measurement result: beam = 6394.694 +/- 3.055 MeV
 :42 changed target to Loop2 LH2
 procudtion, 12:52-01:06 August 25th, target=LH2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
       no beam for the first 100k triggers, beam came back at 15:38
       daq rate=750Hz @ I=78uA,
 procudtion, 01:07-08:56 August 25th, target=LH2, shms_p=5.422,shms_theta=7.5,hms_p=-0.96,hms_theta=29.57,
       daq rate=750Hz @ I=78uA,
 :00 Rotated SHMS to 26.82 deg, HMS to 28.41 deg, shms_p=3.706,shms_theta=26.82,hms_p=-3.514,hms_theta=28.41,
 :16 changed target to dummy, I=40uA
 :35 Rotated SHMS to 23.13 deg, HMS to 33.37 deg, shms_p=4.22,shms_theta=23.13,hms_p=-3.014,hms_theta=33.37,
 :15 changed target to LH2
 procudtion, 08:57-10:27 August 25th, target=LH2, shms_p=4.22,shms_theta=23.13,hms_p=-3.014,hms_theta=33.37,
       daq rate=3.0kHz @ I=78uA,
       beam stopped at 09:03, 777k evnets
 :30 Rotated SHMS  to 8.0 deg and HMS to 42.23deg
 SBSVME22 lost connection. USB stick failed. No access until next accelerator maintenance day.
 can not control MPOD utill the 20220916.
 ==============================================================================================
 pedestal, test daq, no beam, HV on
 pedestal, test daq, no beam, HV on
-Jixie Zhang
+==GEM cable length changed to 20m==
-Jixie Zhang
+20220917 23:23
 gem pedestal run, GEM HV was not on for this run
 trash run, pulser event enabled, unable to check GEM signal
 ==first 100k pulse event are disabled==
 beam seems stopped
 :51 still no beam
 :28 no beam
 :50 still no beam
 :22 beam delivery suspended due to transport ion chamber failure
 Latency check, initial latency value 49
 initial latency value 49 -- (49 is too late)
 & 3326  scan for value 52
 & 3328  scan for value 55 -- (this seems good, also consistent with Ezekiel's INFN setup)
 & 3330 & 3331 & 3332  scan for value 58 (seems too early)
 & 3334 scan for value 64 -- (64 is too early)
 & 3336 scan for value 60 -- (too early)
 production, 00:25 - 11:06 Sep. 19th, run with new GEM latency 55, (55 is too early)
 procudtion, 11:24 Sep 19th - 18:34 Sep. 20th, run with slightly modifed latency 52.
       target=Fe, shms_p=-8.55,shms_theta=8.3,hms_p=1.82,hms_theta=48.3,
 :10 Sep 19th, changed target to B10
 :16 Sep 19th, changed target to B4C-11
 :00 Sep 19th, beam stopped till 00:24 Sep 20th
 :03 Sep 20th, changed target to Ca40, HMS roated to 66.4deg, HMS_p was set to 1.325
       target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
 :00 Sep 20th, RF study started, no beam till 21:12
 production, 01:58 - 12:43 Sep 21st,
       beam was bad, accelarator worked at about 50% efficiency
       target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
 :44, SHMS Q1 vacuum issiu. Beam stopped.
 :54, Beam came back but last for 10 minutes only then went away.
 production,13:07 Sep 21st - 12:03 Sep 22nd,
       target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
 production,12:04 Sep 22nd - 23:35 Sep 22nd,
       target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
 production,23:36 Sep 22nd - 15:21 Sep 23rd,
       target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
       beam stopped due to vacuum issue at around 9:16.
 production,20:06 Sep 23rd -
       target=Ca40,shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
       daq crashed at 02:22 Sep 25th
       Tunl11 lost mounting disk, vncserver can not start properly
 daq crashed, no data file
 productin, 21:02 Sep 25th - 03:51 Sep 26th
       target=carbon, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
       daq rate 250Hz
 target changed to B4C-10
 production, 03:59 - 11:18 Sep 26th
       target=B4C-10, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
       beam stopped at ~05:45
 production, 11:20 Sep 26th - 20:34 Sep 27th, no beam until 20:12 Sep 26th.
       target=B4C-10, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
 :30 target changed to Ca48
       target=Ca48,shms_p=-8.55,shms_theta=8.3,hms_p=1.82,hms_theta=48.33,
 :51 Sep 27th, target changed to Ca40
 :19 Sep 27th, target changed to Carbon
 :35 Sep 27th, target changed to Beryllium
 :12 Sep 27th, target changed to B4C-10
 :40 Sep 27th, target changed to B4C-11
 :00 Sep 27th, target changed to Beryllium
 :42 Sep 27th, target changed to B4C-10
       beam stopped at 17:20, Sep 27th
 production, 20:51, Sep 27th - 15:27 Sep 28th, no beam until 02:49 Sep 28th.
 :18 Sep 27th, target changed to B4C-11
       target=B4C-11, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4,
 :59 Sep 28th, target changed to B4C-10
 :35 Sep 28th, target changed to Beryllium
 production, 15:28, Sep 28th - 10:40 Sep 29th, no beam until 20:12 Sep 26th.
       target=Beryllium, shms_p=-8.55,shms_theta=8.3,hms_p=1.325,hms_theta=66.4, rate=500Hz
 :51 target changed to Loop 1 LD2
 :20 target changed to Fe
       beam stopped at 7:00 Sep 29th.
 Jixie Zhang
 ==SC0_t change to another discriminator unit because the old one has floating threshold==
 Jixie Zhang
 ==TS#3 enabled, which is ShowerSum==
 Jixie Zhang
 ==GEM cable length changed to 30m==
 Jixie Zhang
 trash, daq test
 :14 SHMS rotated to 26deg
 pedestal, 18:21 - 18:27 Sep 29th, no beam
 production, 18:28 Sep 29th - 22:32 Oct 1st, no beam until 22:34
 :04 Sep 29th, target changed to Carbon hole
       target=Carbon Hole, shms_p=-4.935,shms_theta=26.02,hms_p=6.476,hms_theta=20.69,
 :30 Sep 29th, beam stopped
 :31 Sep 29th, target changed to Loop 2 LH2
 :04 Oct 1st, tune beam came back
       target=LH2, shms_p=-4.935,shms_theta=26.02,hms_p=6.476,hms_theta=20.69,
 :38 Oct 1st, target changed to Caron
 :57 Oct 1st, Target changed to LH2
 :01 Oct 1st, SHMS at 9.24 deg and HMS at 29.39 deg
       target=LH2, shms_p=-8,shms_theta=9.24,hms_p=4.17,hms_theta=29.41,
       daq crashed at 18:34
 :28 Oct 1st, SHMS rotated to 10.77, HMS to 31.73
       shms_p=-8,shms_theta=10.77,hms_p=3.76,hms_theta=31.73,
       subrun 00-01:  SHMS=26, Carbon hole + LH2
       subrun 02-23:  SHMS=26deg, LH2
       subrun 24:  SHMS=26deg, LH2 + carbon target
       subrun 25:  SHMS=26deg, Carbon
       subrun 26:  SHMS=26deg, carbon + SHMS=9.24deg LH2 target
       subrun 27-42: shms_theta=9.24, LH2
 production, 22:35 Oct 1st - 23:01 Oct 1st, daq crashed at about 22:55
       target=LH2, shms_p=-8,shms_theta=10.77,hms_p=3.76,hms_theta=31.73,
 :38 Oct 1st, SHMS rotated to 16.55, HMS to 29.4
       target=LH2, shms_p=-8,shms_theta=16.55,hms_p=4.17,hms_theta=29.4, daq rate=7kHz
 production, 23:02 Oct 1st - 23:40 OCt 1st,
       target=LH2, shms_p=-8,shms_theta=16.55,hms_p=4.17,hms_theta=29.4, daq rate=7kHz
 :25 target changed to dummy
       target=dummy, shms_p=-8,shms_theta=16.55,hms_p=4.17,hms_theta=29.4, daq rate=6.7kHz
 ==TS#3 prescale factor set to 10==
 production, 23:42 Oct 1st - 20:43 Oct 2nd
       target=dummy, shms_p=-8,shms_theta=16.55,hms_p=4.17,hms_theta=29.4, daq rate=2.4kHz
 :55 Oct 1st, SHMS rotated to 15.09deg
 :15 Oct 2nd, target change to LH2
       target=LH2,shms_p=-8,shms_theta=15.09,hms_p=3.77,hms_theta=31.72,
 :51 Oct 2nd, SHMS rotated to 13.67deg
 :07 Oct 2nd, target change to dummy
       target=dummy,shms_p=-8,shms_theta=13.67,hms_p=3.35,hms_theta=34.36,
 :37 Oct 2nd, SHMS rotated to 12.24deg
       target=dummy,shms_p=-8,shms_theta=12.24,hms_p=2.94,hms_theta=37.37,
 :08 Oct 2nd,target changed to LH2
 :25 Oct 2nd, SHMS rotated to 10.78deg
       target=LH2,shms_p=-8,shms_theta=10.78,hms_p=2.51,hms_theta=40.97,
 :57 Oct 2nd,target changed to dummy
 :25 Oct 2nd, SHMS rotated to 9.25deg
       target=dummy,shms_p=-8,shms_theta=9.25,hms_p=2.08,hms_theta=45.36,
 :42 Oct 2nd,target changed to LH2
 :30 Oct 2nd, SHMS rotated to 26.02deg
       target=LH2,shms_p=-4.935,shms_theta=26.02,hms_p=6.476,hms_theta=19.55,
 :29 Oct 2nd,target changed to dummy
 :30 Oct 2nd, SHMS rotated to 20.02deg
       target=dummy,shms_p=-6.286,shms_theta=20.02,hms_p=5.107,hms_theta=24.91,
 :02 Oct 2nd,target changed to LH2
 :30 Oct 2nd, SHMS rotated to 15.01deg
       target=LH2,shms_p=-7.626,shms_theta=15.01,hms_p=3.738,hms_theta=31.89,
 :05 Oct 2nd,target changed to dummy
 :30 Oct 2nd, SHMS rotated to 10.02deg
       target=dummy,shms_p=-9.005,shms_theta=10.02,hms_p=2.289,hms_theta=43.13,
 :55 Oct 2nd,target changed to LH2
 :40 Oct 2nd, SHMS rotated to 10.02deg
       target=LH2,shms_p=-9.2,shms_theta=9.26,hms_p=2.076,hms_theta=45.39,
 :05 Oct 2nd,target changed to dummy
 :35 Oct 2nd, SHMS rotated to 7.995deg
       target=dummy,shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
 :30 Oct 2nd,target changed to LH2
 :54 Oct 2nd,SJMS sieve in
 :18 Oct 2nd,target changed to Beryllium,
       target=Be,SHMS Sieve Slit in,shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
 production, 20:44 Oct 2nd - 17:05 Oct 3rd
       target=dummy, shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
 :52 Oct 2nd,target changed to LH2
       target=LH2,SHMS Sieve Slit in,shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
 :28 Oct 2nd,target changed to dummy, SHMS sieve still in
       target=dummy,SHMS Sieve Slit in,shms_p=-9.502,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
 :45 Oct 2nd, SHMS momentum set to -8.55
 :08 Oct 3rd,target changed to LH2
       target=LH2,SHMS Sieve Slit in,shms_p=-8.55,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
 :49 Oct 3rd,target changed to Beryllium,
       target=Beryllium,SHMS Sieve Slit in,shms_p=-8.55,shms_theta=7.995,hms_p=1.739,hms_theta=49.53,
 :28 Oct 3rd,target changed to LH2
 :42 roated SHMS and HMS. Spectrometer Emergency Stop Detected, Hall is open for trouble shooting.
       beam stopped from 1:38.
       Accelerator can not deliver beam since 04:10 Oct 3rd
 ==SHMS roated to 20.02deg, HMS to 20deg==
 production, 18:20 Oct 3rd - 12:14 Oct 4th
 :45 Oct 3rd, tune beam
       target=LH2,shms_p=-4,shms_theta=20.02,hms_p=-4,hms_theta=20.0,
 :05 SHMS and HMS rotated to 25deg
       target=LH2,shms_p=-3.5,shms_theta=25.02,hms_p=-3.5,hms_theta=25.0,
 :22 SHMS and HMS rotated to 25deg
       target=LH2,shms_p=-2.5,shms_theta=35.02,hms_p=-2.5,hms_theta=35.0,
 :27 change momentum to 1.24GeV SHMS
       target=LH2,shms_p=-1.24,shms_theta=35.02,hms_p=-2.5,hms_theta=35.0,
 :19 SHMS rotated to 8 deg, momentum is set to -9.2GeV
 :45 target changed to LD2
       target=LD2,shms_p=-9.2,shms_theta=8,hms_p=-2.5,hms_theta=35.0,
 :45 target changed to C12
       target=Carbon,shms_p=-9.2,shms_theta=8,hms_p=-2.5,hms_theta=35.0,
 :40 Beam is off
 cosmic, 13:30 Oct 4th - 13:40 Oct 5th, no beam for the whole run
 cosmic, 13:42 Oct 5th - 13:49 Oct 6th, no beam for the whole run
 cosmic, 13:51 Oct 6th - 15:24 Oct 6th, no beam for the whole run
 ==change TS#3 prescale factor to 1==
 cosmic, 15:26 Oct 6th - 17:45 Oct 6th, no beam for the whole run
 == enable TS#4, which is VME DSC ELC output ch4 ==
-Jixie Zhang
+production, 17:47 Oct 6th - 01:02 Oct 10th, no beam until 03:22 Oct 9th
 :28 Oct 9th, target changed to Aluminum Hole,shms_p=-9.2,shms_theta=8,hms_p=-1.95,hms_theta=25.99,
 :16 Oct 9th, Target changed to LD2,
 :45 Oct 9th, Target changed to carbon,
 :53 Oct 9th, Target changed to LD2,
 :46 Oct 9th, Target changed to Carbon,
 :16 Oct 9th, Target changed to LD2,
 :26 Oct 9th, Target changed to Carbon,
 :47 Oct 9th, SHMS rotated to 8.5deg
 :40 Oct 9th, Target changed to LD2,shms_p=-9.2,shms_theta=8.50,hms_p=-1.95,hms_theta=25.99,
 :18 Oct 9th, SHMS rotated to 26deg,shms_p=-1.95,shms_theta=26.00,hms_p=-1.95,hms_theta=25.99
 :55 Oct 9th, Target changed to LH2,
 :16 Oct 9th, Target changed to dummy,
 :36 Oct 9th, Target changed to Ca40,
 :00 Oct 9th, Target changed to Carbon,
-Jixie Zhang
+      beam stopped at 19:05 Oct 9th
 Jixie Zhang
 production, 01:02 Oct 10th - 18:23 Oct 10th
-Jixie Zhang
+      target=Carbon,,shms_p=-1.95,shms_theta=26.00,hms_p=-1.95,hms_theta=25.99
 :00 Oct 10th, Target changed to Dummy,
 :24 Oct 10th, Target changed to LD2,
 :51 Oct 10th, Target changed to LH2,
 :15 Oct 10th, both SHMS and HMS momenta changed to -5.42:
       target=LH2,shms_p=-5.42,shms_theta=26.00,hms_p=-5.42,hms_theta=25.99
 :25 Oct 10th, Target changed to LD2,
 :18 Oct 10th, Target changed to Dummy,
 Jixie Zhang
 production, 18:24 Oct 10th - 14:52 Oct 11th
-Jixie Zhang
+      target=Dummy,shms_p=-5.42,shms_theta=26.00,hms_p=-5.42,hms_theta=25.99, daq rate 6.4kHz @60uA
 :25 Oct 10th, Target changed to Ca40,
 :46 Oct 10th, Target changed to Carbon,
 :45 both SHMS and HMS momenta changed to -4.767
       target=Carbon,shms_p=-4.767,shms_theta=26.00,hms_p=-4.767,hms_theta=25.99
 :09 Oct 11th, Target changed to Ca40,
 :18 Oct 11th, Target changed to Dummy,
 :33 Oct 11th, Target changed to LD2,
 :49 Oct 11th, Target changed to LH2,
-Jixie Zhang
+      daq crashed at 06:07 Oct 11th
-Jixie Zhang
+production, 14:54 Oct 11th - 20:52 Oct 11th
       target=LH2,shms_p=-4.767,shms_theta=26.00,hms_p=-4.767,hms_theta=25.99
 :45 both SHMS and HMS momenta changed to -4.19
       target=LH2,shms_p=-4.19,shms_theta=26.00,hms_p=-4.19,hms_theta=25.99,
 :33 Oct 11th, Target changed to LD2,
 Jixie Zhang
-Jixie Zhang
+==disable TS#4 @ 20221011 20:53==
 production, 20:58 Oct 11th - 13:28 Oct 13th
       target=LH2,shms_p=-4.19,shms_theta=26.00,hms_p=-4.19,hms_theta=25.99, daq rate 6.7kHz@60uA
 :12 Oct 11th, Target changed to Dummy,
 :10 Oct 11th, Target changed to Ca40,
       daq crashed at 21:32 Oct 11th
 Jixie Zhang
-Jixie Zhang
+pedestal, 13:32 Oct 13th - 13:44 Oct 13th,
       target=Carbon, shms_p=2.52,shms_theta=26.00,hms_p=2.52,hms_theta=25.99,
 :38 target changed to dummy
       daq crashed
 production, 13:45 Oct 13th - 14:22 Oct 13th
       target=Dummy, shms_p=2.52,shms_theta=26.00,hms_p=2.52,hms_theta=25.99,
       daq crashed
 production, 14:25 Oct 13th - 14:45 Oct 13th
       target=Dummy, shms_p=2.52,shms_theta=26.00,hms_p=2.52,hms_theta=25.99, daq rate 6.2kHz@58uA
       daq crashed
 Jixie Zhang
-Jixie Zhang
+production, 14:52 Oct 13th - 17:55 Oct 13th
 :53 target changed to LD2
       target=LD2, shms_p=2.52,shms_theta=26.00,hms_p=2.52,hms_theta=25.99, daq rate 6.6kHz@58uA
 :24 target changed to LH2
 :12 target changed to Ca40
 :15 both SHMS and HMS momenta changed to -2.21
       target=Ca40, shms_p=2.21,shms_theta=26.00,hms_p=2.21,hms_theta=25.99,
 :05 target changed to Carbon
 production, 17:55 Oct 13th - 23:59 Oct 13th
       target=Carbon, shms_p=2.21,shms_theta=26.00,hms_p=2.21,hms_theta=25.99, daq rate 6.7kHz@60uA
-Jixie Zhang
+:35 target changed to Ca40
 :29 both SHMS and HMS momenta changed to 1.95 GeV/c
       target=Ca40, shms_p=1.95,shms_theta=26.00,hms_p=1.95,hms_theta=25.99
 :15 target changed to Carbon @60uA
 :14 target changed to dummy @40uA
 :46 target changed to Loop2 LH2
 :18 target changed to Loop1 LD2 @60uA
       beam stopped at 22:45 to rotated spectrometers, but failed. SO no beam until 01:30 Oct 14th.
 Jixie Zhang
-Jixie Zhang
+production, 23:59 Oct 13th - 15:02 Oct 14th
-Jixie Zhang
+:20 SHMS rotated to  8 deg, HMS to 20deg
       no beam until 01:30
       target=LD2, shms_p=9.2,shms_theta=8.00,hms_p=3.4,hms_theta=20
 :59 target changed to Carbon
 :24 target changed to Ca40
 :34 target changed to Carbon
 :04 target changed to Loop1 LD2
 :33 HMS momentum changed to 2.71 GeV/c
 :43 target changed to Loop2 LH2
       target=LH2, shms_p=9.2,shms_theta=8.00,hms_p=2.71,hms_theta=20
 :58 target changed to Carbon
 :26 target changed to Ca40
 :02 HMS momentum changed to 2.421 GeV/c
       target=Ca40, shms_p=9.2,shms_theta=8.00,hms_p=2.421,hms_theta=20
 :26 target changed to Beryllium
 :54 target changed to dummy
 :22 target changed to Loop2 LH2
-Jixie Zhang
+      beam stopped at 8 AM
-Jixie Zhang
+production, 15:03 Oct 14th - 02:16 Oct 15th
-Jixie Zhang
+      beam came back at 15:45
       target=LH2, shms_p=9.2,shms_theta=8.00,hms_p=2.421,hms_theta=20
 :05 target changed to Loop1 LD2
-Jixie Zhang
+      daq crashed at 18:35 Oct 14th due to disk is full
 trash, 02:18 Oct 15th - daq could not start
 trash, 02:22 Oct 15th - daq could not start
-Jixie Zhang
+production, 02:28 Oct 15th - 16:48 Oct 15th
-Jixie Zhang
+      target=tin foil (Sn), shms_p=9.2,shms_theta=8.00,hms_p=2.421,hms_theta=20
-Jixie Zhang
+      daq rate 6.4kHz @ 40uA
-Jixie Zhang
+:34  target changed to Ti foil
 :02  target changed to Fe foil
 :02  target changed to Ag foil
 :32  target changed to Th foil
 :03  target changed to Ni-58 foil
 :38  target changed to Ni-64 foil
       beam stopped from 07:02 until 08:36
 :02  both SHMS and HMS change polarity to negative
 :32  target changed to Loop1 LD2
 :36 beam back: target=LD2, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20
-Jixie Zhang
+      daq crashed at 14:14 Oct 15th due to disk is full
 trash, 17:20 Oct 15th - daq could not start
 Jixie Zhang
 production, 17:21 Oct 15th - 13:55 Oct 16th
-Jixie Zhang
+:21 target=Beryllium, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 6.6kHz @ 59uA
 :06 target changed to Ca40
-Jixie Zhang
+      daq crashed sincd 05:42, no beam since 08:55 Oct 16th
-Jixie Zhang
+:15 target changed to Ca48
 Jixie Zhang
 production, 17:58 Oct 16th - 15:26 Oct 17th
-Jixie Zhang
+:40 beam came back
       target=Ca48, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
       daq crashed since 12:47,
 :08 target changed to Carbon
 Jixie Zhang
 Jixie Zhang
-Jixie Zhang
+production, 15:29 Oct 17th - 00:45 Oct 18th
-Jixie Zhang
+      target=Carbon, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
 :38 target changed to B4C-11 (Boron-11)
-Jixie Zhang
+      daq crashed @ 22:45
-Jixie Zhang
+:15 target changed to B4C-10 (B-10)
 Jixie Zhang
 Jixie Zhang
-Jixie Zhang
+production, 00:47 Oct 18th - 00:34 Oct 19th
-Jixie Zhang
+      target=B4C-10, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 4.94kHz @59 uA
 :07 target changed to Sn foil
       no beam since 03:27 till 19:41
 :41-19:57 HallC is doing BCM calibration
 :58 target=Sn, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
 :13 Oct 19th, target changed to Ti foil
 Jixie Zhang
-Jixie Zhang
+production, 00:34 Oct 19th - 13:37 Oct 19th
-Jixie Zhang
+      target=Ti foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
 :54 target changed to Fe foil
-Jixie Zhang
+      no beam since 08:00
 production, 23:54 Oct 19th - 10:59 Oct 20th
-Jixie Zhang
+      no beam until 02:00
       target=Fe foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20,
 :40 target changed to Ag foil
 :17 target changed to Th foil
 :39 target changed to Ni-58 foil
 :58 target=Ni-58 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1250Hz @ 45uA
 Jixie Zhang
-Jixie Zhang
+production, 11:00 Oct 20th - 14:56 Oct 21st
 :02 target=Ni-58 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1250Hz @ 45uA
 :12 target changed to Ni-64 foil
 :51 target moved to home
 :13 target changed to Ni-64 foil
 :20 target=Ni-64 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1500Hz @ 50uA
 :20 target changed to Ni-58 foil
 :08 target changed to Th foil @60uA
 :59 target changed to Ag foil
 :56 target changed to Fe foil
 :23 target changed to Ti foil
 :38 target changed to Sn foil
 :05 target changed to B4C-10 foil
 :25 target changed to B4C-11 foil
 :51 target=B4C-11 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 2964Hz @ 50uA
 production, 11:00 Oct 21st - 14:14 Oct 22nd
 :57 target=B4C-11 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 2964Hz @ 50uA
 :14 target changed to Carbon foil
 :20 target changed to Ca48 foil
 :15 target changed to Ca40 foil
 :33 target changed to Beryllium foil
 :33 target changed to dummy
 :51 target changed to Loop2 LH2
 :04 target changed to Loop1 LD2
 :14 target=LD2, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 4.2KHz @ 30uA
 production, 14:14 Oct 22nd - 04:04 Oct 23rd
 :14 target=LD2, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 4.2KHz @ 30uA
 :24 target changed to Loop2 LH2
 :12 target changed to dummy
 :38 target changed to Beryllium
 :19 target changed to Ca40
 :25 target changed to Ca48
       daq crashed at 01:43 Oct 23rd
 :36 target changed to Carbon
 production, 04:07 Oct 23rd - 15:11 Oct 23rd
 :08 target=Carbon, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 3.0KHz @ 58.5 uA
 :18 target changed to B4C-11 foil
 :13 target changed to B4C-10 foil
 :57 target changed to Sn foil
 :41 target changed to Ti foil
 production, 15:11 Oct 23rd - 10:38 Oct 24th
 :12 target=Ti foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1235Hz @ 40uA
 :04 target changed to Fe foil
 :33 target changed to Ag foil
 :50 target changed to Th foil (Thorium)
 :34 target=Th foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 4.7kHz @ 59uA
 :22 target changed to Ni-58 foil
 :33 target changed to Ni-64 foil
 :37 target=Ni-64 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1482Hz @ 50uA
 Jixie Zhang
-Jixie Zhang
+production, 10:39 Oct 24 - 15:09 Oct 24th
-Jixie Zhang
+:39 target=Ni-64 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-6.6,hms_theta=20, daq rate 1482Hz @ 50uA
 :08 HMS momentum changed to -4.78 GeV/c
-Jixie Zhang
+      target=Ni-64 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20,
-Jixie Zhang
+:28 target changed to Ni-58 foil
 production, 15:09 Oct 24 - 17:20 Oct 24th
       target=Ni-58 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20,
 :50 target changed to Th foil
 :57 target changed to Ag foil
 :19 target=Ag foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20, daq rate 4.2kHz @ 45uA
 ==MPOD Board1 was tripped off, but do not know when it happened, need to find out from replayed data==
 ==change SC0 and SC1 HV by increasing all by 100V==
 Name: SC0_T, SC0_B, SC1_T, SC1_B,
 HV:    1700   1700   1780   1850
 production, 17:31 Oct 24 - 15:12 Oct 25th
 :19 target=Ag foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20,
 :36 target changed to Fe foil
 :50 target=Fe foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20, daq rate 3.5kHz @ 45uA
 :26 target changed to Ti foil
 :20 target=Ti foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20, daq rate 2.7kHz @ 46.5uA
 :56 target changed to B4C-11 foil
 :51 target changed to Carbon foil
 :04 target changed to Ca48 foil
 :21 target changed to Ca40 foil
 :11 target changed to Beryllium foil
 :46 target changed to dummy
 :59 target changed to LH2
 :09 target changed to LD2
 :55 target changed to LH2
 :13 target changed to dummy
 :28 target changed to Beryllium foil
 :43 target changed to Ca40 foil
 :39 target changed to Ca48 foil
 :11 target changed to Carbon foil
 :11 target changed to B4C-11 foil
 :10 target changed to B4C-10 foil
 :32 target changed to Sn foil
 :48 target changed to Ti foil
 :16 target changed to Fe foil
 :42 target changed to Ag foil
       beam stopped at 14:15
 production, 15:25 Oct 25 - 13:52 Oct 26th
       target=Ag foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20
 :28 target changed to Th foil
 :09 target changed to Ag foil
 :15 target=Ag foil, shms_p=-9.2,shms_theta=8.00,hms_p=-4.78,hms_theta=20, daq rate 6.7kHz @ 46uA
 :08 target changed to B4C-10 foil
       daq crashed at 19:31
 :39 target changed to B4C-11 foil
       ...
 :22 target changed to Ca40 foil
 production, 13:55 Oct 26 - 04:10 Oct 27th
       accelerator can not delieve beam until ?
       target=Ca40 foil, shms_p=-9.2,shms_theta=8.00,hms_p=-2.71,hms_theta=20, daq rate 6.7kHz @ 46uA
       coda crashed at 02:55
 production, 04:15 Oct 27 - 08:03 Oct 27th
 :16 target=LD2, shms_p=-9.2,shms_theta=8.00,hms_p=-2.42,hms_theta=20, daq rate 6.7kHz @ 30uA
 ==replace GEM gas bottle,gem gas was empty on Oct25-26==
 ==remove VTP board==
 ==MaROC function added into read-out-list==
 -3430 trash, daq test
 ==add epics variable: target ladder encoder hcBDSPOS==
 ==SHMS changed to 10deg, HMS to 35 deg, spectrometer polarity changed to positive target changed==
 pedestal, 21:01 Oct 27th - 21:04 Oct 27th
 production, 21:06 Oct 27th - 20:32 Oct 28th
       target=Carbon, shms_p=+9.2,shms_theta=10.00,hms_p=+2.11,hms_theta=35,
 :28 target changed to Ca40 foil
       beam stopped at 0:44
 production, 20:33 Oct 28th - 12:40 Oct 29th
       beam came back at 00:49, target at home
 :49 target=home, shms_p=+9.2,shms_theta=10.00,hms_p=+2.11,hms_theta=35,
 :19 target changed to Carbon hole
 :22 target changed to Ca40 foil
 :16 target changed to Loop1 LD2
 :49 target changed to Loop2 LH2
 :31 target changed to dummy
 :02 target changed to Ca40 foil
 :37 target changed to Carbon foil
 :14 target changed to Ca40 foil
 :01 target changed to dummy
 :37 target changed to Loop2 LH2
 :06 target changed to Loop1 LD2
       coda crashed at 12:30 due to disk is full
 ==HMS momentum changed to +1.44==
 production, 12:43 Oct 29th - 14:47 Oct 30th
 :00 target=LD2, shms_p=+9.2,shms_theta=10.00,hms_p=+1.44,hms_theta=35, daq rate=6.7kHz @40uA
 :43 target changed to Loop2 LH2
 :17 target changed to dummy
 :49 target changed to Loop2 LH2
 :14 target changed to dummy
 :55 target changed to Ca40
 :49 target changed to Carbon
       coda crashed at 21:25
 :59 HMS momentum changed to +1.26
       target=Carbon, shms_p=+9.2,shms_theta=10.00,hms_p=+1.26,hms_theta=35,
 :55 target changed to Ca40
       ...
 ==02:34 Oct 30th, change SHMS|HMS polarity to negative, SHMS_p=-9.2, HMS_p=-4.08==
 production, 14:50 Oct 30th - 02:10 Oct 31st
 :00 target=Ca40, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @50uA
 production, 02:10 Oct 31st - 13:30 Oct 31st
 :10 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @50uA
 :30 MPOD HV crate was tripped off
 ==turn MPOD on==
 production, 13:37 Oct 31st - 13:54 Oct 31st
 :40 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
       comparing to run 3436, it seems that 6.7kHz is the maximum daq rate.
       I plan to change the prescale factor to confirm this.
 ==change TS#3 prescale factor from 1 to 2==
 production, 13:56 Oct 31st - 14:02 Oct 31st
 :58 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
 ==change TS#3 prescale factor from 2 to 3==
 production, 14:04 Oct 31st - 14:06 Oct 31st
 :05 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
 ==change TS#3 prescale factor from 3 to 4==
 production, 14:09 Oct 31st - 14 Oct 31st
 :10 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
 ==disable TS#1 and TS#2, change TS#3 prescale factor from 4 to 10==
 production, 14:09 Oct 31st - 14:11 Oct 31st
 :10 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=235Hz @60uA
 ==Enable TS#1 and TS#2, disable TS#3 ==
 production, 14:21 Oct 31st - 14:24 Oct 31st
 :22 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=2.6kHz @60uA
 ==Enable TS#1, TS#2 and TS#3  change TS#3 prescale factor from 10 to 5==
 trash, daq could not start
 ==Enable TS#1, TS#2 and TS#3  change TS#3 prescale factor from 5 to 4==
 production, 14:31 Oct 31st - 14:34 Oct 31st
 :32 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.7kHz @60uA
 ==Enable TS#1, TS#2 and TS#3  change TS#3 prescale factor from 4 to 6==
 trash, daq could not start
 production, 14:38 Oct 31st - 14:40 Oct 31st
 :39 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=4.8kHz @60uA
 ==Enable TS#1, TS#2 and TS#3  change TS#3 prescale factor from 6 to 5==
 production, 14:43 Oct 31st - 14:50 Oct 31st
 :45 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=6.6kHz @60uA
 ==Enable TS#1, TS#2 and TS#3  change TS#3 prescale factor from 5 to 6==
 trash, daq could not start
 production, 14:58 Oct 31st - 23:36 Oct 31st
 :59 target=LD2, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=4.8kHz @60uA
 :09 target changed to Carbon
 production, 23:37 Oct 31st - 11:14 Nov 1st
 :39 target=Carbon, shms_p=-9.2,shms_theta=10.00,hms_p=-4.08,hms_theta=35, daq rate=1.7kHz @55.5uA
 :53 target changed to LD2
 :00 SHMS and HMS momentum changed to -4.0GeV/c, HMS rotated to 20.7deg
       target=LD2, shms_p=-4.0,shms_theta=10.00,hms_p=-4.0,hms_theta=20.7
 :35 SHMS and HMS rotated to 20.deg
       target=LD2, shms_p=-4.0,shms_theta=20.0,hms_p=-4.0,hms_theta=20.0
       beam was off since 09:15
 pedestal, 11:15 Nov 1st,  no beam
 production, 17:40 Nov 1st - 17:47 Nov 1st
       target=LD2, shms_p=-4.0,shms_theta=20.0,hms_p=-4.0,hms_theta=20.0, daq rate 6.67kHz @ 50uA
 ==change TS#3 prescale factor from 6 to 8==
 production, 17:50 Nov 1st - 00:52 Nov 2nd
       target=LD2, shms_p=-4.0,shms_theta=20.0,hms_p=-4.0,hms_theta=20.0, daq rate 5.1kHz @ 50uA
 production, 00:53 Nov 1st - 09:15 Nov 2nd
       target=dummy, shms_p=-4.0,shms_theta=20.0,hms_p=-4.0,hms_theta=20.0, daq rate 741Hz @ 10uA
 pedestal, 18:28 - checking the DAQ after dorking with the maroc readout, no beam
 production, 18:43 Nov 2nd - 01:00 Nov 3rd
       daq machine died at 01:00
 ======================================================
 daq machine tunl11 is dead
 new daq mahine  uvasolid is up ...
 ======================================================
 -3458  trash, debug daq
 pedestal, 22:30 Nov 11th - 21:34 Nov 11th, no beam
 production, 22:30 Nov 11th, - 15:49 Nov 12th
       target=LD2, shms_p=-9.2,shms_theta=9.85,hms_p=-2.72,hms_theta=35.01, daq rate 3.0kHz @60uA
 production, 15:41 Nov 12th, - 16:00 Nov 13rd
 target=Ca40, shms_p=-9.2,shms_theta=9.85,hms_p=-2.72,hms_theta=35.01, daq rate 2.5kHz @50uA
       coda stopped at 15:50 (uvasolid reboot?)
 trash, 03:01 Nov 14th, - 03:45 Nov 14th
       target=Beryllium, shms_p=-9.2,shms_theta=9.85,hms_p=-2.4,hms_theta=35.01, daq rate 250Hz @50uA
       MPOD HV board1 read back does not match set values......
 production, 03:47 Nov 14th, - 15:40 Nov 14th
       target=Beryllium, shms_p=-9.2,shms_theta=9.85,hms_p=-2.4,hms_theta=35.01, daq rate 1.7kHz @50uA
       MPOD board1 was tripped off, need to check from data when it happen
 production, 15:42 Nov 14th, - 04:00 Nov 15th
       target=Ca40, shms_p=-9.2,shms_theta=9.85,hms_p=-2.4,hms_theta=35.01, daq rate 3kHz @55uA
 production, 04:06 Nov 15th, - 07:00 Nov 15th
       target=Ca40, shms_p=-9.2,shms_theta=9.85,hms_p=-1.63,hms_theta=35.01
 ===================================================
 - 3529  trash, debug maroc-ssp daq
 ===================================================
 == SHMS at 20deg ==
 ==TS#2 changed from "Top_PreShower & Top_Shower" to "Left_PreShoer & Left_Shower"==
 - 3533  trash, debug daq for prescale factor
 ==change DAC values for fadc slot8.7 and slot8.9 in fadc config file==
 # for TS#2 = Top_Shower & Top_PreShower
 #FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3170 3170 3440 3450 3470 3460 3450 3440 3390
 # for TS#2 = Left_Shower & Left_PreShower
 FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3470 3170 3140 3450 3470 3460 3450 3440 3390
 ==determine prescale factors (from run 3534 to 3536),  Finalize it from run 3537==
 ==Disable TS#1 and TS#3, only TS#2 is on, prescale_factor is 0 ==
 production, 11:34 Nov 17th, - 11:46 Nov 17th
       target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 4.5kHz @60uA
       target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 3.8kHz @50uA
       target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 3.1kHz @40uA
 ==Disable TS#1 and TS#2, only TS#3 is on, prescale_factor is 8 ==
 production, 11:50 Nov 17th, - 11:56 Nov 17th
       target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 270Hz @40uA
 ==Disable TS#2 and TS#3, only TS#1 is on, prescale_factor is 0 ==
 production, 11:34 Nov 17th, - 11:46 Nov 17th
       target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 2.7kHz @40uA
       target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 2.0kHz @30uA
 ==Enable TS#1, S#2 and TS#3, prescale_factors are 0,1,5 ==
 production, 12:05 Nov 17th, - 12:18 Nov 17th
       target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 3.3kHz @30uA
 production, 12:20 Nov 17th, - 21:06 Nov 17th
       target=Carbon, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 2.4kHz @20uA
 :56 target changed to LD2
       target=LD2, shms_p=-4,shms_theta=20,hms_p=-4,hms_theta=20, daq rate 5.7kHz @50uA
 trash, 21:08 Nov 17th, - 21:12 Nov 17th
       no beam but got 7kHz daq rate, why .....?
 pedestal 21:15 Nov 17th, -21:17 Nov 17th, no beam
 ==SHMS rotated to =26.41deg=
 ==TS#2 changed from "Left_PreShower & Left_Shower" to "Right_PreShoer & Right_Shower"==
 trash 16:02 Nov 18th, -16:04 Nov 18th, no beam ,debug daq
 == changed FADC  config file ==
 #FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3170 3170 3440 3450 3470 3460 3450 3440 3390
 # for TS#2 = Left_Shower & Left_PreShower
 #FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3470 3170 3140 3450 3470 3460 3450 3440 3390
 # for TS#2 = Right_Shower & Right_PreShower
 FADC250_ALLCH_DAC 3450 3150 3390 3140 3160 3150 3140 3170 3470 3140 3450 3470 3460 3450 3440 3390
 cosmic 16:11 Nov 18th, - 16:18 Nov 18th, no beam,
       TS#1, TS#2 and TS#3 have prescale factors 0,1,5,first 100k are pulse trigger
 == set  all prescale factor to 0 for cosmic, turn off pulse trigger ==
 cosmic 16:19 Nov 18th, - ? Nov 18th, no beam,
       TS#1, TS#2 and TS#3 have prescale factors 0,0,0, no pulse trigger, daq rate is 15Hz
 == 17:30pm 18Nov2022 test maroc readout with everything else ==
 - 3552 trash, debug maroc daq
 production,  18:42 Nov 18th - 18:42 Nov 18th, daq rate ~7kHz
       target=LH2, shms_p=-4.78,shms_theta=26.55,hms_p=-4.78,hms_theta=26.5, daq rate 7kHz @60uA
       this run has no prescale factors
       daq is saturated, I need to apply the prescale factor ....
 == TS#1, TS#2 and TS#3 have prescale factors 0,1,5,first 100k are pulse trigger ==
 production, 18:42 Nov 18th - 13:12  Nov 19th
       target=LH2, shms_p=-4.78,shms_theta=26.55,hms_p=-4.78,hms_theta=26.5, daq rate 4.6kHz @60uA
       dummy target, daq rate 3.3kHz @ 40uA
       MPOD HV boards were both tripped off at around 12:00
 production, 13:14 Nov 19th - 03:37 Nov 20th
       target=Ca48, shms_p=-9.2,shms_theta=8,hms_p=-2.72,hms_theta=35,
 MPOD board2 read back values are zero for run 3556 and 3557, data mightnot be good
 production(? need to check data), 03:37 Nov 20th - 16:51 Nov 20th
       target=LD2, shms_p=-9.2,shms_theta=8.13,hms_p=-4.08,hms_theta=35, daq rate 6.2kHz @30uA
 production?(need to check), 16:53 Nov 20th - 17:03 Nov 20th
       target=LD2, shms_p=-9.2,shms_theta=8.13,hms_p=-4.08,hms_theta=35, daq rate 1.8kHz @30uA
       MPOD board2 read back values are zero
 = reboot MPOD crate ==
 production, 17:37 Nov 20th - 09:23 Nov 21st
       target=LD2, shms_p=-9.2,shms_theta=8.13,hms_p=-4.08,hms_theta=35, daq rate 5kHz @30uA
 :20 ghost daq rate 3-5kHz @no beam
 pedestal, 09:27 Nov 21st - 09:43 Nov 21st, no beam
 production, 00:22 Nov 22nd - 12:35 Nov 22nd
       target=LD2, shms_p=-9.2,shms_theta=8.13,hms_p=-4.08,hms_theta=35, daq rate 5.2kHz @60uA
 pedestal, 12:35 Nov 22nd - 12:40 Nov 22nd
       no beam but daq rate ~5.2kHz @ 0uA, firmware bug
 pedestal, 12:45 Nov 22nd - 14:35 Nov 22nd
 ==rol changed to solve ghost rate ==
 production, 14:35 Nov 22nd - 14:40 Nov 22nd
       target=dummy, shms_p=-3.57,shms_theta=34.46,hms_p=-3.57,hms_theta=34.28
 production, 14:42 Nov 22nd - 11:12 Nov 23rd
       target=dummy, shms_p=-3.57,shms_theta=34.3,hms_p=-3.57,hms_theta=34.28
 pedestal, debug gem with pulse
 -3567  trash
 pedestal, debug gem with pulse
 ==fixed GEM cable loose connection problem ==
 -3570  pedestal, debug gem with pulse
 production, 23:22 Nov 23rd - ? Nov 24th
       target=dummy, shms_p=-3.57,shms_theta=35.17,hms_p=-4.08,hms_theta=34.99, daq rate = 4kHz @40uA
 :50 coda crashed
 production, 13:24 Nov 24th - 00:41 Nov 25th
       target=dummy, shms_p=-3.57,shms_theta=35.17,hms_p=-4.08,hms_theta=34.99, daq rate = 4kHz @40uA
       MPOD were wtripped at 13:38
 ==SHMS moved to 8.5 deg ==
 pedestal, HVs are not on
 pedestal, HVs are not on
 production, 12:03 Nov 25th - 13:57 Nov 25th
       target=B4C-11, shms_p=-9.2,shms_theta=8.66,hms_p=-3.09,hms_theta=34.99, daq rate = 3kHz @70uA
 :24  SHMS rotated to 11 deg
       coda crashed at 13:30
 production, 13:59 Nov 25th - 15:06 Nov 25th
       target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 3kHz @70uA
       coda crashed at 14:36
 production, 15:08 Nov 25th - 15:22 Nov 25th
       target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99
       coda crashed at 15:15
 production, 15:24 Nov 25th - 16:48 Nov 25th
       target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99
 ==reverted Ben's modification in rol==
 production, 17:02 Nov 25th - 17:19 Nov 25th
       target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 5kHz @70uA
 production, 17:21 Nov 25th - 21:16 Nov 25th
       target=B4C-11, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 5kHz @70uA
 production, 21:18 Nov 25th - 02:43 Nov 26th
       target=B4C-10, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 4kHz @70uA
 ==MPOD board1 HV was tripped off, it might affect run# 3582 - 3585==
 production, 02:45 Nov 26th - ? Nov 26th - crashed ~3:17am
       target=B4C-10, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99, daq rate = 4kHz @70uA
 testrun after crash recovery
 == Updated rol to remote doOnce hack ==
 production, 13:28 Nov 26th - 14:57 Nov 26th
       target=B4C-10, shms_p=-9.2,shms_theta=11.16,hms_p=-3.09,hms_theta=34.99
 :40 SHMS roated to 10 deg, HMS momentum changed to -2.72GeV/c
       target=B4C-10, shms_p=-9.2,shms_theta=10.16,hms_p=-2.72,hms_theta=34.99
 MPOD board1 HV was tripped off, it might affect run# 3582 - 3585
 production, 14:59 Nov 26th - 15:10 Nov 26th
       target=B4C-10, shms_p=-9.2,shms_theta=10.16,hms_p=-2.72,hms_theta=34.99, daq rate 700Hz @ 70uA
 == reboot MPOD board1 ==
 production, 15:13 Nov 26th - ? Nov 26th
       target=B4C-10, shms_p=-9.2,shms_theta=10.16,hms_p=-2.72,hms_theta=34.99, daq rate 4kHz @ 70uA
 :57 coda crashed
 production, 04:36 Nov 27th - ? Nov 27th
 :13 coda crashed
 production, 13:40 Nov 27th - 00:31 Nov 28th
       target=B4C-10, shms_p=-9.2,shms_theta=10.16,hms_p=-2.4,hms_theta=34.99, daq rate 4kHz @ 70uA
 production, 00:33 Nov 28th - 09:30 Nov 28th
       target=Beryllium, shms_p=-9.2,shms_theta=10.16,hms_p=-4.08,hms_theta=34.99, daq rate 3.5kHz @ 60uA
       coda stoped at 04:05 due to disk full.
 :20  beam is off.
 pedestal, 09:38 Nov 28th -10:03 Nov 28th, no beam
 ==switched to  config hallc_fadc_ssp_maroc==
 pedestal, 14:35 Nov 30th -14:35 Nov 30th, no beam, test maroc coda config
 -3595 pedestal, test maroc coda config
 ==switched back to  config hallc_fadc_ssp=
 production, 13:18 Dec 3rd - 20:38 Nov 28th
 -3599 trash, coda can not start
 production, 20:47 Dec 3rd - ? Nov 28th
       coda crashed at  21:12. Mpod  board2 crashed.
 == reboot MPOD board2 ==
 -3603 trash, coda can not start
 ==switched to  config hallc_fadc_ssp_maroc==
 -3607 trash, coda can not start
 ==reboot vme crate==
 ==switched to  config hallc_maroc==
 -3617  trash, coda can not start
 == 20221207 12:20  reboot MPD and LV of GEM ==
 -3621 debug maroc coda
 ==MPOD board1 tripped, it affects runs 3608-3621, reboot MPOD board1==
 === reconnect daq for high rate triggers, fadc config file changed ===
 set all prescale to zero.  GEM HVs are connected to mpod board1
 FADC slot7 DAC set to 3300
 FADC250_DAC 3300
 SC0 top and SC1 top were delayed by 32ns
 -3623 trash, debug daq,
 slot7:
 FADC250_ALLCH_DAC  3310 3280 3280 3300 3150 3140 3150 3150 3280 3320 3450 3190 3140 3190 3130 3450
 slot8:
 FADC250_ALLCH_DAC  3450 3150 3390 3140 3160 3150 3140 3320 3320 3290 3450 3470 3460 3150 3440 3390
 debug daq, data is useful but has latency issue, 01:26 Dec 14th - 10:40 Dec 14th
       Cherenkov sum is 40ns earlier than shower sum, SC0_top and SC1_top is 6ns earlier than shower sum after 32ns delay
       N625 FIFO will introduce 8-10 ns of delay.
 == Cherenkov sum delay by 40ns, SC0_top and SC1_top delay 6ns more ==
 ==shower sum also connected to vmeDSC ch#4,  whose 4th twist pin is connected to TS#4 in TI==
 production 19:28 Dec 14th - 19:36 Dec 14th
 ==change FADC slot7.15 DAC value  from 3450 to 3310 ==
 slot7: FADC250_ALLCH_DAC  3310 3280 3280 3300 3150 3140 3150 3150 3280 3320 3450 3190 3140 3190 3130 3310
 production 19:39 Dec 14th - 23:57 Dec 14th
 production 00:00 Dec 15th - 11:15 Dec 15th
 production 13:19 Dec 15th - 23:41 Dec 15th
 == updated rol:  TS#4 only, no pulse triggers ==
 trash, 23:43 Dec 15th - 23:45 Dec 15th
 debug vmeDSC, does not work
 == updated rol:  turn on TS#1, TS#2,TS#3 and TS#4, with pulse triggers for first 100k events ==
 Note that TS#4 is still not working, although TS#4 prescale factor is set to 5
 production 23:50 Dec 15th - 10:41 Dec 16th
 :59 DISK is full,  it might affect subrun  27-40
 production 10:46 Dec 16th - 19:20 Dec 16th
 :35 target=dummy, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 735Hz @40uA
 production 19:50 Dec 16th - 04:23 Dec 17th
      no beam at the beginning
 :58 target=Beryllium, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 3.2kHz @60uA
      Livetime went to zero as soon as I took a look.
 test to make sure daq still ok.
      took some pedestal
 -3670  trash, no data files
 ====================================================================================================
 Moving DAQ to uvasolid2 - Bryan... 17dec2022 - 4:30am
 production, 04:33 Dec 17th - 13:15 Dec 17th
 production 13:19 Dec 17th - 13:24 Dec 17th
 ==only TS#4 is enabled, disabled internal pulse triggers ==
 debug TS#4,trash, 13:35 Dec 17th - 13:37 Dec 17th
      TS#4 is not working yet, daq rate = 0 @ 40uA
 ==only TS#3 is enabled, disabled internal pulse triggers ==
 debug TS#3,trash, 13:40 Dec 17th - 13:49 Dec 17th
      TS#3 is not working yet,, daq rate = 1~2Hz @ 40uA
 ==only TS#2 is enabled, disabled internal pulse triggers ==
 production, 13:52 Dec 17th - 14:09 Dec 17th
 :08 target=He-3, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 490Hz @40uA
 ==only TS#1 is enabled, disabled internal pulse triggers ==
 production, 14:11 Dec 17th - 14:15 Dec 17th
 :12 target=He-3, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 245Hz @40uA
 == TS#1-#4 are all enabled, enabled internal pulse triggers ==
 production, 14:17 Dec 17th - 22:22 Dec 17th
      no beam for the first 100k pulse triggers.  Maximum daq rate 6860Hz
 :20 target=He-3, shms_p=-9.2,shms_theta=8.5,hms_p=-4.08,hms_theta=34.99, daq rate = 735Hz @40uA
 == updated sbsvme22 to use uvasolid2 - 22:22 Dec 17
 production, 22:45 Dec 17th - 01:31 Dec 18th
      beam stop at 23:56
 production, 01:41 Dec 18th - 15:32 Dec 18th
      no beam for the first 100k pulse triggers.
 production, 15:34 Dec 18th - 00:00 Dec 19th
 :35 target=Ca-40, shms_p=-9.2,shms_theta=8.5,hms_p=-3.57,hms_theta=34.99, daq rate = 4.4kHz @60uA
 :45 target = Beryllium, daq rate = 3kHz @ 60uA
 :58 target = He-4 10cm, daq rate = 2.7kHz @ 40uA
 production, 00:01 Dec 19th - 09:47 Dec 19th
 :02 target=He-4 10cm, shms_p=-9.2,shms_theta=8.5,hms_p=-3.57,hms_theta=34.99, daq rate = 2.7kHz @40uA
 :06 change target to dummy, daq rate = 1.2kHz @ 40uA
      beam stopped at 7:20.  Happy wnter break!!!
 cosmic, first 100k events are internal pulse trigger
 =====================================================================
 ==trigger bit 1 is "Cer_sum or Shower_sum"==
 cosmic, first 100k events are internal pulse trigger
 =====================================================================
 Hall C cosmic test. Ecal is vertically placed. From the top to the bottom,
 it is SC_top, GEM, Shower, PreShower, SC_bottom.
 Led is placed inside the Cherenkov tank, driven by a 1kHz retangular wave (2,5V, 100ns width).
 Trigger: TS#1 is the 1kHz retangular pulse, TS#2=SC_top & Shower_Sum & SC_bottom
 TS#4 is Shower_sum  using vmeDSC, prescale factor 5.
 config = hallc_fadc_ssp_maroc
 good maroc debug data
 -3707 trash, debug coda
 -3709  hallc_fadc_ssp
 hallc_fadc_ssp_maroc
 hallc_fadc_ssp_maroc
 TS#2 only
 bottom 5x10cm sc (117) goes to fadc8.3
 sc light guide only (102) goes to fadc8.5
 sc 2 inches x 3 inches  (540) goes to fadc8.1
 bottom SC fadc8.0
 top SC fadc8.2
 TS#2 only, good data
 -3762 debug daq
 cosmic production, 03:18 Dec 23rd - 11:43 Dec 23rd
       TS#2(SC_top(5mv) & SC_bottom(5mv)) and TS#4(Shower_Sum(5mv)),good data
 Add 2 more SC:
 pershower tile just above the GEM, connected to signal lable 448(goes to FADC8.4), Hv cable 252
 inch by 2inch by 8inch  SC was placed on top of preshower, connected to signal lable 538(goes to FADC8.6), Hv cable 249
 vmeDSC(start from 1):
 (SC_bottom), 2(SC_top), 3(Shower_sum,not_use), 4(shower_sum goes to TS#4),...,
 (preshower_sum_not_use),8(SC_kedi6_tile)
 TS#2 is "SC_top(5mv) & SC_bottom(5mv)", TS#3 is "SC_top(5mv) & SC_tile(5mv)", TS#4 is "Shower_Sum(5mv)"
 junk
 cosmic production, 14:55 Dec 23rd - 18:26 Dec 23rd,
       no GEM, TS#234
 cosmic production, 18:29 Dec 23rd- 01:06 Dec 24th,
       with GEM, TS#234
 cosmic production, 01:10 Dec 24th - 09:16 Dec 24th
 cosmic production, 09:17 Dec 24th -16:53 Dec 24th
 cosmic production, 16:53 Dec 24th - 00:13 Dec 25th
 cosmic production, 00:14 Dec 25th - 09:23 Dec 25th
 cosmic production, 09:24 Dec 25th - 11:28 Dec 25th
 cosmic production, 12:01 Dec 25th - 12:08 Dec 25th
 cosmic production, 12:13 Dec 25th - 15:58 Dec 25th
 cosmic production, 16:04 Dec 25th - 23:55 Dec 25th
 cosmic production, 23:57 Dec 25th - 09:27 Dec 26th
 cosmic production, 09:38 Dec 26th - 16:59 Dec 26th
 cosmic production, 16:59 Dec 26th - 00:08 Dec 27th
 cosmic production, 00:08 Dec 27th - 10:30 Dec 27th
 cosmic production, 12:00 Dec 27th - 16:37 Dec 27th
 cosmic production, 16:48 Dec 27th - 09:47 Dec 28th
 cosmic production, 10:57 Dec 28th - 08:51 Dec 29th
 cosmic production. 10:00 Dec 29th - 16:19 Dec 29th
 -3821 Cherenkov LED run
 ==FADC will record 100 samples from run 3822==
 cosmic production. 00:30 Dec 30th - 00:56 Dec 30th
 cosmic production. 03:00 Dec 30th - 10:04 Dec 30th
 swap preshower left and right
 cosmic production, but shower blocks are still has 120 deg rotation
 rotate the shower blocks by 120deg
 old: top(SDU#4), right(SDU#5), left(THU#2)
 new: top(SDU#5), right(THU#2), left(SDU#4)   This is the same as beamtest
 -3862 Cherenkov LED run with raw sum
 cosmic production. 06:30 Dec 30th - 21:17 Dec 30th
 ==HV scan for Cherenkov MaPMT==
 -3867 Cherenkov LED run with raw sum
 ==GEM HV is off, Cherenkov HVs stay at -950V==
 cosmic production. 22:04 Dec 30th - 12:49 Dec 31st
 Cherenkov LED run, 13:21 Dec 31st - 13:45 Dec 31st
 Cherenkov LED run, 13:47 Dec 31st - 15:47 Dec 31st
 cosmic production. 15:50 Dec 31st - 01:05 Jan 1st 2023
 cosmic production. 01:05 Jan 1st - 17:47 Jan 1st 2023
 cosmic production. 17:48 Jan 1st - 15:30 Jan 2nd 2023
 cosmic production. 15:32 Jan 2nd - 0:09 Jan 3rd 2023
 ==GEM HV is on==
 cosmic production. 00:09 Jan 3rd - 11:20 Jan 3rd 2023
 cosmic production. 11:21 Jan 3rd - 13:33 Jan 3rd 2023
 ==slot7 FADC delay by 40ns==
 cosmic production. 13:35 Jan 3rd - 13:37 Jan 3rd 2023
 ==slot7 FADC delay by 160ns==
 cosmic production. 13:40 Jan 3rd - 14:11 Jan 3rd 2023
 -------------------------------------------------------------------
 ==Cherenkov HVs change from 950,950,950,950 to 1050,1050,1100,1050==
 cosmic production. 13:40 Jan 3rd - 14:48 Jan 3rd 2023
 -------------------------------------------------------------------
 ==change FADC slot8 delay==
 FADC250_ALLCH_DELAY 80 80 80 80 80 80 80 40 40 40 40 40 40 40 40 0
 cosmic production. 14:49 Jan 3rd - 17:56 Jan 3rd 2023
 -------------------------------------------------------------------
 HV changes: old: SC__top(1900), SC_bottom(1750), SC_E(1000)
 New:
 Name:_SC_top,_SC_bottom, ...,SC_E
 HV:_____1800,______1850, ...,1100
 cosmic production. 14:49 Jan 3rd - 17:56 Jan 3rd 2023
 cosmic production. 17:57 Jan 3rd - 00:56 Jan 4th 2023
 cosmic production. 00:57 Jan 4th - 01:55 Jan 4th
 -------------------------------------------------------------------
 ==HV changed for _SC_bottom and shower_r and shower_l==
 old:
 board1, 6kV, 8-ch:
 Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
 HV:___0,_3750,_0,_______________1640,_______________1800,_______________1550,_0,_0
 board2, 2kV, 16-ch:
 Name:_SC_top,_SC_bottom,_SC_B,_SC_C,___CerA,___CerB,___CerC,___CerD,_SC_A,_Shower_R(THU#2),_Shower_L(SDU#4),_Shower_T(SDU#5),__,__,_SC_E,_SC_D
 HV:_____1800,______1850,_1700,_1600,___1050,___1050,___1100,___1050,_1600,____________1050,____________1030,_____________850,_0,_0,_1100,_1250
 -------------------------------------------------
 new:
 board1, 6kV, 8-ch:
 Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
 HV:___0,_3750,_0,_______________1640,_______________1800,_______________1550,_0,_0
 board2, 2kV, 16-ch:
 Name:_SC_top,_SC_bottom,_SC_B,_SC_C,___CerA,___CerB,___CerC,___CerD,_SC_A,_Shower_R(THU#2),_Shower_L(SDU#4),_Shower_T(SDU#5),__,__,_SC_E,_SC_D
 HV:_____1800,______1800,_1700,_1600,___1050,___1050,___1100,___1050,_1600,_____________950,_____________930,_____________850,_0,_0,_1100,_1250
 -------------------------------------------------
 cosmic production. 01:56 Jan 4th - 08:07 Jan 4th
  - ended to work on c1725
 -------------------------------------------------------------------
 ==Change HVs for Preshower_T(SDU#2), Preshower_L(SDU#1) and SC_Top==
 new:
 Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
 HV:___0,_3750,_0,_______________1750,_______________1800,_______________1600,_0,_0
 board2, 2kV, 16-ch:
 Name:_SC_top,_SC_bottom,_SC_B,_SC_C,___CerA,___CerB,___CerC,___CerD,_SC_A,_Shower_R(THU#2),_Shower_L(SDU#4),_Shower_T(SDU#5),__,__,_SC_E,_SC_D
 HV:_____1850,______1750,_1700,_1600,___1050,___1050,___1100,___1050,_1600,_____________950,_____________930,_____________850,_0,_0,_1100,_1250
 -------------------------------------------------
 -3888 trash, HVs are off
 cosmic production. 16:06 Jan 4th - 19:21 Jan 4th
 cosmic production. 19:22 Jan 4th - 19:40 Jan 4th
 -------------------------------------------------------------------
 ==Change HVs for Preshower_T(SDU#2), Preshower_L(SDU#1) and Preshower_R(THU#1)==
 Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
 HV:___0,_3750,_0,_______________1800,_______________1750,_______________1650,_0,_0
 cosmic production. 19:41 Jan 4th - 23:08 Jan 4th
       GEM HV tripped during the run
 cosmic production. 23:09 Jan 4th - 23:45 Jan 4th
 -------------------------------------------------------------------
 ==Change HVs for Preshower_T(SDU#2) and Preshower_R(THU#1)==
 Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
 HV:___0,_3750,_0,_______________1640,_______________1800,_______________1650,_0,_0
 cosmic production. 23:46 Jan 4th - 00:38 Jan 5th
 cosmic production. 00:39 Jan 5th - 00:54 Jan 5th
 -------------------------------------------------------------------
 ==Change HVs for Preshower_T(SDU#2) and Preshower_L(SDU#1)==
 Name:_X,_GEM1,_X,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1),_X,_X
 HV:___0,_3750,_0,_______________1800,_______________1800,_______________1550,_0,_0
 cosmic production. 00:54 Jan 5th - 08:38 Jan 5th
 trash
 ==cosmic test for preshower==
 only SC_top, SC_bottom, and 3 PreShowers are used. 3 PreShowers are stacked in one pile.
 Trigger is "SC_top & SC_bottom"
 ----------------------------------------------------
 Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
 HV:____1850,_1750,_______________1640,_______________1800,_______________1550
 hallc_fadc config
 cosmic production, SDU#2 does not connect well
 cosmic production, all works
 hallc_fadc_ssp config
 cosmic production
 cosmic production, 21:35 Jan 5th - 23:25 Jan 5th
 ----------------------------------------------------
 Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
 HV:____1850,_1750,_______________1800,_______________1800,_______________1550
 hallc_fadc config
 cosmic production, 23:27 Jan 5th - 00:22 Jan 6th
 ----------------------------------------------------
 Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
 HV:____1850,_1750,_______________1800,_______________1900,_______________1550
 ==> best matched: 1800, 1900,1580
 cosmic production, 00:33 Jan 6th - 01:37 Jan 6th
 ----------------------------------------------------
 Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
 HV:____1850,_1750,_______________1900,_______________2000,_______________1650
 cosmic production, 01:37 Jan 6th - 02:34 Jan 6th
 ----------------------------------------------------
 Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
 HV:____1850,_1750,_______________1710,_______________1800,_______________1500
 cosmic production, 02:35 Jan 6th - 03:31 Jan 6th
 ----------------------------------------------------
 Name:SC_top,_GEM1,_Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
 HV:____1850,_1750,_______________1730,_______________1800,_______________1515
 cosmic production, 03:35 Jan 6th - 07:36 Jan 6th
 ==============================================================================
 Summary of preshower gain match cosmic test
 run#       _Preshower_T(SDU#2),_Preshower_R(THU#1),_Preshower_L(SDU#1)
 -3900  _______________1640,_______________1800,_______________1550
 _______________1800,_______________1800,_______________1550
 _______________1800,_______________1900,_______________1550
 _______________1900,_______________2000,_______________1650
 _______________1710,_______________1800,_______________1500
 _______________1730,_______________1800,_______________1515   (best)
 another predicted matched HVs: 1800, 1900, 1580
 =======================================================

Project

General

Profile

SoLID DAQ » SoLID ECal

Hallc beamtest runlist » History » Version 9